manualshive.com logo in svg

Dodge Dakota 2001, Руководство по обслуживанию

Service Manual для Dodge Dakota 2001 - это подробное руководство, которое поможет вам обслуживать и ремонтировать ваш автомобиль. Скачайте это руководство бесплатно с manualshive.com и сохраните его для использования в любое удобное время. Надежное руководство для вашего Dodge Dakota 2001!

Поделиться
Скачать
background image

SERVICE CAUTIONS

CAUTION: Liquid refrigerant is corrosive to metal
surfaces. Follow the operating instructions supplied
with the service equipment being used.
Never add R-12 to a refrigerant system designed to
use R-134a. Damage to the system will result.
R-12 refrigerant oil must not be mixed with R-134a
refrigerant oil. They are not compatible.
Do not use R-12 equipment or parts on the R-134a
system. Damage to the system will result.
Do not overcharge the refrigerant system. This will
cause excessive compressor head pressure and
can cause noise and system failure.
Recover the refrigerant before opening any fitting
or connection. Open the fittings with caution, even
after the system has been discharged. Never open
or loosen a connection before recovering the refrig-
erant.
Do not remove the secondary retention clip from
any spring-lock coupler connection while the refrig-
erant system is under pressure. Recover the refrig-
erant before removing the secondary retention clip.
Open the fittings with caution, even after the sys-
tem has been discharged. Never open or loosen a
connection before recovering the refrigerant.
The refrigerant system must always be evacuated
before charging.
Do not open the refrigerant system or uncap a
replacement component until you are ready to ser-
vice the system. This will prevent contamination in
the system.
Before disconnecting a component, clean the out-
side of the fittings thoroughly to prevent contami-
nation from entering the refrigerant system.
Immediately after disconnecting a component from
the refrigerant system, seal the open fittings with a
cap or plug.
Before

connecting

an

open

refrigerant

fitting,

always install a new seal or gasket. Coat the fitting
and seal with clean refrigerant oil before connect-
ing.
Do not remove the sealing caps from a replacement
component until it is to be installed.
When installing a refrigerant line, avoid sharp
bends that may restrict refrigerant flow. Position the
refrigerant lines away from exhaust system compo-
nents or any sharp edges, which may damage the
line.
Tighten refrigerant fittings only to the specified
torque. The aluminum fittings used in the refriger-
ant system will not tolerate overtightening.
When disconnecting a refrigerant fitting, use a
wrench on both halves of the fitting. This will pre-
vent twisting of the refrigerant lines or tubes.
Refrigerant oil will absorb moisture from the atmo-

sphere if left uncapped. Do not open a container of
refrigerant oil until you are ready to use it. Replace
the cap on the oil container immediately after using.
Store refrigerant oil only in a clean, airtight, and
moisture-free container.
Keep service tools and the work area clean. Con-
tamination of the refrigerant system through care-
less work habits must be avoided.

CAUTION - REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS

Kinks or sharp bends in the refrigerant plumbing

will reduce the capacity of the entire system. High
pressures are produced in the system when it is oper-
ating. Extreme care must be exercised to make sure
that all refrigerant system connections are pressure
tight.

A good rule for the flexible hose refrigerant lines is

to keep the radius of all bends at least ten times the
diameter of the hose. Sharp bends will reduce the
flow of refrigerant. The flexible hose lines should be
routed so they are at least 80 millimeters (3 inches)
from the exhaust manifold. It is a good practice to
inspect all flexible refrigerant system hose lines at
least once a year to make sure they are in good con-
dition and properly routed.

There are two types of refrigerant fittings:

•

All fittings with O-rings need to be coated with

refrigerant oil before installation. Use only O-rings
that are the correct size and approved for use with
R-134a refrigerant. Failure to do so may result in a
leak.

•

Unified plumbing connections with gaskets can-

not be serviced with O-rings. The gaskets are not
reusable and new gaskets do not require lubrication
before installing.

Using the proper tools when making a refrigerant

plumbing connection is very important. Improper
tools or improper use of the tools can damage the
refrigerant fittings. Always use two wrenches when
loosening or tightening tube fittings. Use one wrench
to hold one side of the connection stationary, while
loosening or tightening the other side of the connec-
tion with a second wrench.

The refrigerant must be recovered completely from

the system before opening any fitting or connection.
Open the fittings with caution, even after the refrig-
erant has been recovered. If any pressure is noticed
as a fitting is loosened, tighten the fitting and
recover the refrigerant from the system again.

Do not discharge refrigerant into the atmosphere.

Use an R-134a refrigerant recovery/recycling device
that meets SAE Standard J2210.

The refrigerant system will remain chemically sta-

ble as long as pure, moisture-free R-134a refrigerant

AN

PLUMBING

24 - 33

PLUMBING (Continued)

Содержание Dakota 2001




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dakota 2001

Jacobsen Cushman Turf Truckster Parts & Maintenance Manual preview
Cushman Turf Truckster
Бренд: Jacobsen Страницы: 210
FormFit HD 23A 07 Installation Instructions preview
HD 23A 07
Бренд: FormFit Страницы: 4
Mazda 2008 MX-5 Miata Manual preview
2008 MX-5 Miata
Бренд: Mazda Страницы: 400
Wagan Wireless Handsfree Car Kit User Manual preview
Wireless Handsfree Car Kit
Бренд: Wagan Страницы: 20
Flash Cover MN002 Installation Manual preview
MN002
Бренд: Flash Cover Страницы: 2
EUFAB 16465 Operating Instructions Manual preview
16465
Бренд: EUFAB Страницы: 12
AEM 30-3500 Instruction Manual preview
30-3500
Бренд: AEM Страницы: 27
Ferve F-2024 Operating Instructions Manual preview
F-2024
Бренд: Ferve Страницы: 28
BENDIX A-18 TRAILER ABS Manual preview
A-18 TRAILER ABS
Бренд: BENDIX Страницы: 40
Toyota RAV4 HV 2016 Quick Reference Manual preview
RAV4 HV 2016
Бренд: Toyota Страницы: 56
Toro Security Cage Kit Installation Instructions Manual preview
Security Cage Kit
Бренд: Toro Страницы: 8
Thule 1597 Instructions preview
1597
Бренд: Thule Страницы: 4
Safe Fleet Prime Design OCM-3032 Quick Start Manual preview
Prime Design OCM-3032
Бренд: Safe Fleet Страницы: 4
r.LiNK RL2-MMI3G-Q3 Manual preview
RL2-MMI3G-Q3
Бренд: r.LiNK Страницы: 21
Toyota Tundra guide Manual preview
Tundra guide
Бренд: Toyota Страницы: 672
Dodge Charger SRT 392 2017 Operating Information Manual preview
Charger SRT 392 2017
Бренд: Dodge Страницы: 576
Lexus LS 500h 2022 Owner'S Manual, Quick Manual preview
LS 500h 2022
Бренд: Lexus Страницы: 108
Audiovox Prestige 128-8602 Installation Manual preview
Prestige 128-8602
Бренд: Audiovox Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды