manualshive.com logo in svg

Dodge Dakota 2001, Руководство по обслуживанию

Service Manual для Dodge Dakota 2001 - это подробное руководство, которое поможет вам обслуживать и ремонтировать ваш автомобиль. Скачайте это руководство бесплатно с manualshive.com и сохраните его для использования в любое удобное время. Надежное руководство для вашего Dodge Dakota 2001!

Поделиться
Скачать
background image

(6) Disconnect the headlamp and dash wire har-

ness connector for the wiper motor from the wiper
motor pigtail wire connector.

(7) Disconnect the headlamp and dash wire har-

ness ground connector from the wiper motor ground
terminal.

(8) Remove the wiper module from the cowl ple-

num as a unit.

INSTALLATION

(1) Position the wiper module into the cowl ple-

num as a unit.

(2) Reconnect the headlamp and dash wire harness

ground connector to the wiper motor ground terminal
(Fig. 11).

(3) Reconnect the headlamp and dash wire harness

connector for the wiper motor to the wiper motor pig-
tail wire connector.

(4) Reach into the cowl plenum to align the wiper

module mounting bracket with the locations for the
mounting screws.

(5) Install and tighten the four screws that secure

the wiper module bracket to the cowl plenum panel
and the dash panel. Tighten the screws to 8 N·m (72
in. lbs.).

(6) Reinstall the cowl plenum cover/grille panel

over the top of the cowl plenum. (Refer to 23 - BODY/
EXTERIOR/COWL GRILLE - INSTALLATION).

(7) Reinstall the wiper arms onto the wiper pivots.

(Refer to 8 - ELECTRICAL/WIPERS/WASHERS/
WIPER ARMS - INSTALLATION).

(8) Reconnect the battery negative cable.

WIPER RELAY

DESCRIPTION

The wiper relay (or intermittent wipe relay) is

located in the Power Distribution Center (PDC) near
the battery in the engine compartment. See the fuse
and relay layout label affixed to the inside surface of
the PDC cover for wiper relay identification and loca-
tion. The wiper relay is a conventional International
Standards Organization (ISO) micro relay. Relays
conforming to the ISO specifications have common
physical dimensions, current capacities, terminal pat-
terns, and terminal functions. The relay is contained
within a small, rectangular, molded plastic housing.
The relay is connected to all of the required inputs
and outputs through its PDC receptacle by five male
spade-type terminals that extend from the bottom of
the relay base. The ISO designation for each termi-
nal is molded into the base adjacent to the terminal.
The ISO terminal designations are as follows:

•

30 (Common Feed) - This terminal is con-

nected to the movable contact point of the relay.

•

85 (Coil Ground) - This terminal is connected

to the ground feed side of the relay control coil.

•

86 (Coil Battery) - This terminal is connected

to the battery feed side of the relay control coil.

•

87 (Normally Open) - This terminal is con-

nected to the normally open fixed contact point of the
relay.

•

87A (Normally Closed) - This terminal is con-

nected to the normally closed fixed contact point of
the relay.

The wiper relay cannot be adjusted or repaired. If

the relay is damaged or faulty, it must be replaced.

OPERATION

The wiper relay (or intermittent wipe relay) is an

electromechanical switch that uses a low current
input from the Central Timer Module (CTM) to con-
trol a high current output to the low speed brush of
the wiper motor. The movable common feed contact
point is held against the fixed normally closed con-
tact point by spring pressure. When the relay coil is
energized, an electromagnetic field is produced by the
coil windings. This electromagnetic field draws the
movable relay contact point away from the fixed nor-
mally closed contact point, and holds it against the
fixed normally open contact point. When the relay
coil is de-energized, spring pressure returns the mov-
able contact point back against the fixed normally
closed contact point. A resistor or diode is connected
in parallel with the relay coil in the relay, and helps
to dissipate voltage spikes and electromagnetic inter-
ference that can be generated as the electromagnetic
field of the relay coil collapses.

The wiper relay terminals are connected to the

vehicle electrical system through a connector recepta-
cle in the Power Distribution Center (PDC). The
inputs and outputs of the wiper relay include:

•

The common feed terminal (30) is connected to

the wiper motor low speed brush through the wiper
control circuitry of the multi-function switch on the
steering column. When the wiper relay is de-ener-
gized, the common feed terminal is connected to the
wiper park switch output through the CTM on the
front wiper park switch sense circuit. The wiper park
switch output may be battery current (wipers are not
parked), or ground (wipers are parked). When the
wiper relay is energized, the common feed terminal
of the relay is connected to battery current from a
fuse in the Junction Block (JB) through a fused igni-
tion switch output (run-acc) circuit.

•

The coil ground terminal (85) is connected to the

relay control output of the CTM through the wiper
relay control circuit. The CTM controls the ground
path for this circuit internally to energize or de-ener-
gize the wiper relay based upon its programming,
inputs from the wiper and washer control circuitry of

AN

WIPERS/WASHERS

8R - 17

WIPER MODULE (Continued)

Содержание Dakota 2001




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dakota 2001

ZAPTEC Go Instruction Manual preview
Go
Бренд: ZAPTEC Страницы: 240
Davis Instruments 8127 Installation Instructions Manual preview
8127
Бренд: Davis Instruments Страницы: 16
PAC GM1A-R Quick Start Manual preview
GM1A-R
Бренд: PAC Страницы: 4
Nav TV AUDI A6 Installation Manual preview
AUDI A6
Бренд: Nav TV Страницы: 5
Dodge Ram Commercial2016 Owner'S Manual preview
Ram Commercial2016
Бренд: Dodge Страницы: 675
Jeep WRANGLER 2017 User Manual preview
WRANGLER 2017
Бренд: Jeep Страницы: 292
Mopar 82214480 Manual preview
82214480
Бренд: Mopar Страницы: 17
Prorack K349 Fitting Instructions Manual preview
K349
Бренд: Prorack Страницы: 13
TOP VEHICLE TECH GR3FORD5 Installation Manual preview
GR3FORD5
Бренд: TOP VEHICLE TECH Страницы: 8
Smappee EVB-1332-BL-E Installation Manual preview
EVB-1332-BL-E
Бренд: Smappee Страницы: 28
Scosche VQ2M Manual preview
VQ2M
Бренд: Scosche Страницы: 32
Volvo 2009 S40 Owner'S Manual preview
2009 S40
Бренд: Volvo Страницы: 286
FAAFTECH FT-RC-RN Installation Manual preview
FT-RC-RN
Бренд: FAAFTECH Страницы: 2
Stack ROLL POD Installation Manual preview
ROLL POD
Бренд: Stack Страницы: 4
Dodge 2009 RAM TRUCK Owner'S Manual preview
2009 RAM TRUCK
Бренд: Dodge Страницы: 543
Chevrolet 2003 Venture Owner'S Manual preview
2003 Venture
Бренд: Chevrolet Страницы: 490
Champion 97053CH User Manual preview
97053CH
Бренд: Champion Страницы: 5
Champion 94842CH User Manual preview
94842CH
Бренд: Champion Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды