manualshive.com logo in svg

Dodge Dakota 2001, Руководство по обслуживанию

Service Manual для Dodge Dakota 2001 - это подробное руководство, которое поможет вам обслуживать и ремонтировать ваш автомобиль. Скачайте это руководство бесплатно с manualshive.com и сохраните его для использования в любое удобное время. Надежное руководство для вашего Dodge Dakota 2001!

Поделиться
Скачать
background image

when it is provided a path to ground by the instru-
ment cluster transistor. The instrument cluster will
turn on the check gauges indicator for the following
reasons:

•

Bulb Test - Each time the ignition switch is

turned to the On position the check gauges indicator
is illuminated for about two seconds as a bulb test.

•

Engine Temperature High Message - Each

time the cluster receives a message from the PCM
indicating the engine coolant temperature of a gaso-
line engine is about 122° C (253° F) or higher, or a
diesel engine is about 112° C (233° F) or higher, the
check gauges indicator will be illuminated. The indi-
cator remains illuminated until the cluster receives a
message from the PCM indicating that the tempera-
ture of a gasoline engine is about 119° C (246° F) or
lower, a diesel engine is about 109° C (226° F) or
lower, or until the ignition switch is turned to the Off
position, whichever occurs first.

•

Engine Oil Pressure Low Message - Each

time the cluster receives a message from the PCM
indicating the engine oil pressure of a gasoline
engine is about 3.45 kPa (0.5 psi) or lower, or a diesel
engine is about 51.71 kPa (7.5 psi) or lower, the
check gauges indicator will be illuminated. The indi-
cator remains illuminated until the cluster receives a
message from the PCM indicating that the engine oil
pressure of a gasoline engine is above 3.45 kPa (0.5
psi), a diesel engine is above 51.71 kPa (7.5 psi), or
until the ignition switch is turned to the Off position,
whichever occurs first. The cluster will only turn the
indicator on in response to an engine oil pressure low
message if the engine speed is greater than zero.

•

System Voltage Low Message - Each time the

cluster receives a message from the PCM indicating
the electrical system voltage is less than 11.5 volts,
the check gauges indicator will be illuminated. The
indicator

remains

illuminated

until

the

cluster

receives a message from the PCM indicating the elec-
trical system voltage is greater than 12.0 volts (but
less than 16.6 volts), or until the ignition switch is
turned to the Off position, whichever occurs first.

•

System Voltage High Message - Each time

the cluster receives a message from the PCM indicat-
ing the electrical system voltage is greater than 16.6
volts, the check gauges indicator will be illuminated.
The indicator remains illuminated until the cluster
receives a message from the PCM indicating the elec-
trical system voltage is less than 16.1 volts (but
greater than 11.5 volts), or until the ignition switch
is turned to the Off position, whichever occurs first.

•

Actuator Test - Each time the cluster is put

through the actuator test, the indicator will be
turned on, then off again during the bulb check por-
tion of the test to confirm the functionality of the
LED and the cluster control circuitry.

The PCM continually monitors the engine temper-

ature, oil pressure, and electrical system voltage,
then sends the proper messages to the instrument
cluster. For further diagnosis of the check gauges
indicator or the instrument cluster circuitry that con-
trols the LED, (Refer to 8 - ELECTRICAL/INSTRU-
MENT CLUSTER - DIAGNOSIS AND TESTING).
For proper diagnosis of the PCM, the PCI data bus,
or the message inputs to the instrument cluster that
control the check gauges indicator, a DRBIII

t

scan

tool is required. Refer to the appropriate diagnostic
information.

COOLANT LOW INDICATOR

DESCRIPTION

A coolant low indicator is only found in the instru-

ment clusters of vehicles equipped with an optional
diesel engine. The coolant low indicator is located in
the Information Center area of the instrument clus-
ter, to the left of center. The coolant low indicator
consists of a stenciled cutout of the words “LOW
COOLANT” in the opaque layer of the instrument
cluster overlay. The dark outer layer of the overlay
prevents the indicator from being clearly visible
when it is not illuminated. A red lens behind the cut-
out in the opaque layer of the overlay causes the
“LOW COOLANT” text to appear in red through the
translucent outer layer of the overlay when the indi-
cator is illuminated from behind by a Light Emitting
Diode (LED) soldered onto the instrument cluster
electronic circuit board. The coolant low indicator is
serviced as a unit with the instrument cluster.

OPERATION

The coolant low indicator gives an indication to the

vehicle operator when the engine coolant level is low.
This indicator is controlled by a transistor on the
instrument cluster circuit board based upon cluster
programming and electronic messages received by
the cluster from the Powertrain Control Module
(PCM)

over

the

Programmable

Communications

Interface (PCI) data bus. The coolant low indicator
Light Emitting Diode (LED) receives battery current
on the instrument cluster electronic circuit board
through the fused ignition switch output (run-start)
circuit whenever the ignition switch is in the On or
Start positions; therefore, the LED will always be off
when the ignition switch is in any position except On
or Start. The LED only illuminates when it is pro-
vided a path to ground by the instrument cluster
transistor. The instrument cluster will turn on the
coolant low indicator for the following reasons:

8J - 16

INSTRUMENT CLUSTER

AN

CHECK GAUGES INDICATOR (Continued)

Содержание Dakota 2001




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dakota 2001

Happy Orange USB-C Quick Start Manual preview
USB-C
Бренд: Happy Orange Страницы: 2
Wagan 2591 User Manual preview
2591
Бренд: Wagan Страницы: 12
Ford F-150 2018 Quick Reference Manual preview
F-150 2018
Бренд: Ford Страницы: 12
Chevrolet Avalanche 2005 Owner'S Manual preview
Avalanche 2005
Бренд: Chevrolet Страницы: 494
Ford FIESTA ST 2019 Supplement Manual preview
FIESTA ST 2019
Бренд: Ford Страницы: 37
Harbor Freight Tools 66242 User Manual preview
66242
Бренд: Harbor Freight Tools Страницы: 12
Honda 0SR95-HL4-211A Installation Instructions preview
0SR95-HL4-211A
Бренд: Honda Страницы: 3
Ford 2004 Freestar Workshop Manual preview
2004 Freestar
Бренд: Ford Страницы: 8
Intec CVD500LCD Installation And Operation Manual preview
CVD500LCD
Бренд: Intec Страницы: 16
Meta System FrontPlate4 Manual preview
FrontPlate4
Бренд: Meta System Страницы: 16
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
Caraudio-Systems RL-LR12-TF Manual preview
RL-LR12-TF
Бренд: Caraudio-Systems Страницы: 9
Buick 1997 Skylark Owner'S Manual preview
1997 Skylark
Бренд: Buick Страницы: 371
Brodit ProClip 854399 Installation Instructions preview
ProClip 854399
Бренд: Brodit Страницы: 2
APS iBoard IB-R159 Manual preview
iBoard IB-R159
Бренд: APS Страницы: 4
National Cycle Quantum Wash'n'Wipe N30205 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30205
Бренд: National Cycle Страницы: 12
RAWLINK 36772 Instruction Manual preview
36772
Бренд: RAWLINK Страницы: 25
Waeco MagicWatch MWE850 Installation And Operating Manual preview
MagicWatch MWE850
Бренд: Waeco Страницы: 200

Бренды по названию

Популярные бренды

Загрузить еще бренды