manualshive.com logo in svg

Dodge Dakota 2001, Руководство по обслуживанию

Service Manual для Dodge Dakota 2001 - это подробное руководство, которое поможет вам обслуживать и ремонтировать ваш автомобиль. Скачайте это руководство бесплатно с manualshive.com и сохраните его для использования в любое удобное время. Надежное руководство для вашего Dodge Dakota 2001!

Поделиться
Скачать
background image

The text “O/D OFF” appears in an amber color and
at the same lighting level as the gear selector indica-
tor information when it is illuminated by the instru-
ment cluster electronic circuit board. The overdrive
off indicator is serviced as a unit with the VFD in
the instrument cluster.

OPERATION

The overdrive off indicator gives an indication to

the vehicle operator when the Off position of the
overdrive off switch has been selected, disabling the
electronically controlled overdrive feature of the auto-
matic transmission. This indicator is controlled by
the instrument cluster circuit board based upon clus-
ter programming and electronic messages received by
the cluster from the Powertrain Control Module
(PCM)

over

the

Programmable

Communications

Interface (PCI) data bus. The overdrive off indicator
receives battery current on the instrument cluster
electronic circuit board through the fused ignition
switch output (run-start) circuit whenever the igni-
tion switch is in the On or Start positions; therefore,
the indicator will always be off when the ignition
switch is in any position except On or Start. The
indicator only illuminates when it is switched to
ground by the instrument cluster circuitry. The
instrument cluster will turn on the overdrive off indi-
cator for the following reasons:

•

Bulb Test - Each time the ignition switch is

turned to the On position the overdrive off indicator
is illuminated for about two seconds as a bulb test.

•

Overdrive Off Lamp-On Message - Each time

the cluster receives an overdrive off lamp-on message
from the PCM indicating that the Off position of the
overdrive off switch has been selected, the overdrive
off indicator will be illuminated. The indicator
remains illuminated until the cluster receives an
overdrive off lamp-off message from the PCM, or
until the ignition switch is turned to the Off position,
whichever occurs first.

•

Actuator Test - Each time the cluster is put

through the actuator test, the overdrive off indicator
will be turned on, then off again during the VFD por-
tion of the test to confirm the functionality of the
VFD, and again during the bulb check portion of the
test to confirm the functionality of the cluster control
circuitry.

The PCM continually monitors the overdrive off

switch to determine the proper outputs to the auto-
matic transmission. The PCM then sends the proper
overdrive off lamp-on and lamp-off messages to the
instrument cluster. For further diagnosis of the over-
drive off indicator or the instrument cluster circuitry
that controls the indicator, (Refer to 8 - ELECTRI-
CAL/INSTRUMENT CLUSTER - DIAGNOSIS AND
TESTING). For proper diagnosis of the overdrive con-

trol system, the PCM, the PCI data bus, or the mes-
sage inputs to the instrument cluster that control the
overdrive off indicator, a DRBIII

t

scan tool is

required. Refer to the appropriate diagnostic infor-
mation.

SEATBELT INDICATOR

DESCRIPTION

A seatbelt indicator is standard equipment on all

instrument clusters. The seatbelt indicator is located
in the Information Center area of the instrument
cluster, to the right of center. The seatbelt indicator
consists of a stencilled cutout of the International
Control and Display Symbol icon for “Seat Belt” in
the opaque layer of the instrument cluster overlay.
The dark outer layer of the overlay prevents the indi-
cator from being clearly visible when it is not illumi-
nated. A red lens behind the cutout in the opaque
layer of the overlay causes the icon to appear in red
through the translucent outer layer of the overlay
when the indicator is illuminated from behind by a
Light Emitting Diode (LED) soldered onto the instru-
ment cluster electronic circuit board. The seatbelt
indicator is serviced as a unit with the instrument
cluster.

OPERATION

The seatbelt indicator gives an indication to the

vehicle operator of the status of the driver side front
seatbelt. This indicator is controlled by a transistor
on the instrument cluster circuit board based upon
cluster programming and a hard wired input from
the seatbelt switch in the driver side front seatbelt
retractor through the seat belt indicator driver cir-
cuit. The seatbelt indicator Light Emitting Diode
(LED) receives battery current on the instrument
cluster electronic circuit board through the fused
ignition switch output (run-start) circuit whenever
the ignition switch is in the On or Start positions;
therefore, the indicator will always be off when the
ignition switch is in any position except On or Start.
The LED only illuminates when it is switched to
ground by the instrument cluster transistor. The
instrument cluster will turn on the seatbelt indicator
for the following reasons:

•

Seatbelt Reminder Function - Each time the

cluster receives a battery current input on the fused
ignition switch output (run-start) circuit, the indica-
tor will be illuminated as a seatbelt reminder for
about seven seconds, or until the ignition switch is
turned to the Off position, whichever occurs first.
This reminder function will occur regardless of the
status of the seatbelt switch input to the cluster.

AN

INSTRUMENT CLUSTER

8J - 27

OVERDRIVE OFF INDICATOR (Continued)

Содержание Dakota 2001




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dakota 2001

Hama Neptun Manual preview
Neptun
Бренд: Hama Страницы: 6
Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Бренд: Harmar Mobility Страницы: 10
GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Бренд: GMC Страницы: 20
RAM Ram Dodge 2010 Owner'S Manual preview
Ram Dodge 2010
Бренд: RAM Страницы: 616
Nav TV AUDI-P60H Install Manual preview
AUDI-P60H
Бренд: Nav TV Страницы: 9
Honda Clarity 2018 Owner'S Manual preview
Clarity 2018
Бренд: Honda Страницы: 81
GReddy 12519101 Instruction Manual preview
12519101
Бренд: GReddy Страницы: 12
Enduro EM203 User Manual preview
EM203
Бренд: Enduro Страницы: 52
Honda CRV 2015 Navigation Manual preview
CRV 2015
Бренд: Honda Страницы: 253
Toyota 2018 yaris Vehicle Instruction Card preview
2018 yaris
Бренд: Toyota Страницы: 11
iSimple IS7705 Installation & Operation Manual preview
IS7705
Бренд: iSimple Страницы: 8
HUSKY LINERS 47954 Installation Instructions preview
47954
Бренд: HUSKY LINERS Страницы: 4
iOttie HLCRIO138 Manual preview
HLCRIO138
Бренд: iOttie Страницы: 19
Kargo Master 408TC Installation Manual preview
408TC
Бренд: Kargo Master Страницы: 14
Thermo King V-520 RT Series Installation Manual preview
V-520 RT Series
Бренд: Thermo King Страницы: 56
Witter DT144AU Fitting Instructions preview
DT144AU
Бренд: Witter Страницы: 2
Dodge 2008 Dakota Owner'S Manual preview
2008 Dakota
Бренд: Dodge Страницы: 439
Directed 403.NISS4HT 2.36 RSR Installation Manual preview
403.NISS4HT 2.36 RSR
Бренд: Directed Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды