djpower FLAME MACHINE HF-210 Скачать руководство пользователя страница 6

 

- 5 - 

4.

 

SETUP 

4.1.

 

AC Power 

 The machine has two kinds of voltage power supply, it can work with an input voltage of AC 110 V-120 V, 50/60 Hz or AC 220 V-240 V, 
50/60 Hz, depending on the specific model. 

 

To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed 
to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current 
draw under normal conditions. 

Always connect the product to a protected circuit (circuit breaker or fuse). Make sure the product has an appropriate 

electrical ground to avoid the risk of electrocution or fire. 

 

Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves 
only as a 0 to 100% switch. 

4.2.

 

AC Plug 

 The Flame Machine HF-210 comes with a power input cord terminated with a Lockable Powerkon connector on one end and an EU plug 
on the other end (EU & China market). If the power input cord that came with your product has no plug, or if you need the change the plug, 
use the table below to wire the new plug: 

Connection

 

Wire (U.S.)

 

Wire (Europe)

 

AC Live

 

Black 

Brown 

AC Neutral

 

White 

Blue 

AC Ground

 

Green/Yellow 

Green/Yellow 

 

4.3.

 

Resetting the Breaker 

This product is equipped with a resettable breaker. If the breaker trips, all sections of this product will lose power. 

 

 Remove the power cord from mains power. 

 

Reset the breaker by pressing the button with your finger.   

 

Plug the product’s power cord into the power outlet and continue using as recommended.  

5.

 

OPERATION 

5.1.

 

Preparing for Operation 

Before operating the machine, please follow the below steps to prepare: 

 

Before operation, please ensure that there are no flammable materials around the machine, and people and equipment should maintain 
a certain safe distance. Safety distances for HF-210: At least 15m in all projection directions, at least 5m to the other sides of the device. 

 

After checking that all the parts are intact and complete, position the machine on flat. 

 

Please connect the communication line before the power is turned on, and ensure that the communication command is non-injected 
and the device is in test mode. 

 

Always connect the product to a grounded circuit. Before power on, make sure it is connected with the rated voltage 

 

The operator should near the machine and be able to directly see the status,  and immediately terminate the performance when there is 
a danger. There should be a total AC power switch near the operator. When an abnormality occurs, the power should be disconnected 
in time. This is the safest way to do this. 

Содержание FLAME MACHINE HF-210

















Отзывы: