manualshive.com logo in svg

Dixie Narco DPSL5 E, Техническое руководство

Поделиться
Скачать
Dixie Narco DPSL5 E Скачать руководство пользователя страница 21

PROGRAMMING 

 

20 

Single Board Controller (SBC) Software Update 
Procedure 

 

This document describes how to update software on the Single Board Controller (SBC).  

Note:  

All 

existing software revisions, except software version 804,919,240.11, will automatically update the 
software revision upon installation.  For SBC boards using 804,919,240.11 software menu programming 
is required to manually update the software.  Note: All Dr Pepper SL5 Venders require software version 
804,919,240.61 or higher.

 

Important: 

EPROM’s containing software is sensitive to Electrostatic Discharge (ESD).  Failure to 

handle the EPROM carefully could cause damage, which may result in a failed Single Board Controller 
(SBC).   
 

ALWAYS KEEP THE EPROM IN THE ESD TUBE.  GROUND YOURSELF ON THE VENDER CABINET 
BEFORE REMOVING THE EPROM FROM THE ESD TUBE OR CONTROL BOARD.  AN EPROM CAN BE 
USED TO PROGRAM MANY VENDERS, AS LONG AS CARE IS TAKEN NOT TO DAMMAGE THE EPROMS 
LEGS. 
 
ALWAYS TURN POWER OFF BEFORE REMOVING OR INSTALLING EPROMS IN THE CONTROL BOARD. 

 

Important Notes

:  Use the SBC programming manual to program a vender that has a Single Board 

Controller (SBC) installed.  Resetting the machine’s model number is required when updating the space 
to sales default for Dr Pepper SL5 DN501E-10 machines only (software revisions 804,919,240.41C, 
804,919,240.51 and higher).  The model number reset will make the new space to sales default settings 
operational.  The procedure to reset the model number is provided in section IV. 
 

I.

 

EPROM removal 

•

 

Power down the Vender.  

Ground yourself on the vender cabinet before removing the 

EPROM from the ESD tube or control board.

 

•

 

If the EPROM is present in the SBC, remove the existing EPROM from the SBC. 

•

 

Note: An EPROM does not need to be in the board after the SBC has been 
programmed.  The EPROM can be used to reprogram other boards. 

•

 

Verify the pins of the new EPROM are not bent before installing in the EPROM socket. 

•

 

Install the new EPROM in the EPROM socket.  Ensure the EPROM is oriented correctly 
with its reference marker (locator) in the same direction as the reference marker (locator) 
of the EPROM socket.  Do not rely on the EPROM label for orientating the EPROM.  
See Figure 1. 

 

II.

 

Automatic Reprogramming (all software revisions 

except

 804,919,240.11) 

•

 

Turn power on to Vender.  When auto-updating, the display will remain blank while the 
red LED on the board blinks rapidly for 3-4 seconds.  Verify the new software version is 
shown on the display.  If the new software version (the software version of the newly 
installed EPROM) displays, the SBC software has been successfully updated.  If not, 
verify the EPROM is seated properly, with the reference marker oriented correctly and 
follow instructions for manual update if updating from 804,919,240.11.  If problems still 
exist, contact the Dixie-Narco Technical Service Department. 

 

Содержание DPSL5 E














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды