Dive Gear Express DGX Gears XTRA Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 32

background image

5. Carefully slide the Piston Assembly into the End Cap/Port Swivel Assembly – Fig. 37. Using the

previously assembled Washer/O-ring/Teflon Washer stack, insert the stack into the HP side of the

regulator Body (11), as shown on the schematic. Slightly twist the tool, and the stack will come off in

the body - Fig. 38.

Fig. 37 Fig. 38

6. Reverse the tool to hold the stack and protect the Piston end - Fig. 39. Insert the Piston/End Cap/Port

Swivel assembly into the Body and screw it on hand tight - Fig. 40.

Fig. 39 Fig. 40

«
...
21
22
23
24
25
...
»

Содержание DGX Gears XTRA

































Отзывы:

Нет отзывов

Похожие инструкции для DGX Gears XTRA

Бренд: Ebyte Страницы: 34

Бренд: XVision Страницы: 28

Бренд: YASKAWA Страницы: 61

Бренд: Gardner Denver Страницы: 22

Бренд: B&G Страницы: 2

Бренд: Gatekeeper Страницы: 28

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: Yamaha Страницы: 92

Бренд: Ziton Страницы: 36

Бренд: ZIMMERLI MESSTECHNIK Страницы: 12

Бренд: H-Tronic Страницы: 32

Бренд: Gardigo Страницы: 6

Бренд: VAT Страницы: 14

UNDER CONTROL CP-30A PILOT

Бренд: G-Force Страницы: 2

AMES 4000SS Series

Бренд: Watts Страницы: 8

MT600iWP Series

Бренд: weintek Страницы: 2

Бренд: NEC Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды