Dive Gear Express DGX Gears XTRA Скачать руководство пользователя страница 24

Страница: 24 / 32

7. Install the first stage handle into a high pressure port - Fig. 41. Use the Multi-Tool to tighten the End

Cap/Port Swivel assembly to the Body. A piece of rubber may be used to lessen the chance of

scratching the End Cap - Fig. 42. Tighten the connection so that no gap is visible, and the connection

is secure. There is no torque specification for this.

Fig. 41 Fig. 42

8. Set the assembly aside and install the O-ring (30*) in the HP side of the body, as shown using a blunt

brass or plastic pick, and place the Spring (29) on top of the Washer Stack - Fig. 43. Install the O-ring

(32*) onto the HP Seat Retainer (33) and place the HP Seat (31*) into the HP Seat Retainer. Orient the

seat with the concave side (arrow indicates detail) towards the Piston and the flat side facing the HP

Seat Retainer - Fig. 44.

Fig. 43 Fig. 44

Содержание DGX Gears XTRA

































Результаты поиска

Содержание DGX Gears XTRA

Отзывы:

Похожие инструкции для DGX Gears XTRA

Бренды по названию

Популярные бренды

Dive Gear Express DGX Gears XTRA, Руководство по обслуживанию

Результаты поиска

Содержание DGX Gears XTRA

Отзывы:

Похожие инструкции для DGX Gears XTRA

Бренды по названию

Популярные бренды