Directed Electronics 560XV Скачать руководство пользователя

Страница: 45 / 55

2-10 CHANNEL 4 VALIDITY/LATCHED/LATCHED RESET WITH IGNITION/30 SECOND TIMED/90 SECOND TIMED

OUTPUT:

This wire provides a (-) 200mA output whenever the transmitter button(s) controlling Channel 4 is

pressed. This output can be programmed to provide the following types of outputs (see also the

Feature Menus

section):

■

Validity:

Output that will send a signal as long as the transmission is received.

■

Latched:

Output that will send a signal when the Channel 4 button(s) is pressed and will continue until the

same button(s) is pressed again.

■

Latched, reset with ignition:

Similar to the latched output, this type of output turns on the first time the

Channel 4 button(s) is pressed and turns off the next time the same button is pressed. This type of output

additionally stops and resets whenever the ignition is turned on and then off.

■

30-second timed:

Output that will send a continuous signal for 30 seconds.

■

90-second timed:

Output that will send a continuous signal for 90 seconds.

2-11 CHANNEL 5 VALIDITY/LATCHED/LATCHED RESET WITH IGNITION/30 SECOND TIMED/90 SECOND TIMED

OUTPUT:

Channel Four can be programmed for these output configurations. The unit is set to the default valid-

ity output. To change the configuration, use the two-chirp setting to toggle through the different configurations.

Refer to channel 4 feature 2-10 for additional detail.

3-1 ENGINE CHECKING ON/OFF:

In the default setting the remote start will monitor either the vehicle's tach

wire or voltage depending on the programming of feature 3-2. If programmed OFF the vehicle will crank for the

programmed crank time (feature 3-5) and will not verify with tach or voltage that the car is running. In the OFF

setting, if the vehicle fails to start, the ignition can stay on for the entire run duration. Using tach or voltage

check is always recommended if possible.

3-2 CHECKING TYPE TACH/VOLTAGE:

Selects the method of engine monitoring. If set to TACHOMETER the unit

will reference the learned tach signal to disengage the starter. In addition it will monitor the RPM and shut down

if the engine RPM is too high or too low. When set to VOLTAGE, the unit will crank the starter for the programmed

time and then attempt to sense that the engine is running by detecting an increase in voltage. The threshold for

the voltage check is selectable in feature 3-6.

3-3 RUN TIME 12, 24, 60 MINUTES:

Selects the time in minutes that the system will operate the engine

until the system "times out". This is the maximum operation period and the system may be shut down

using a shutdown at any time. Using the Bitwriter, the run time can be programmed for any duration from 1-60

minutes.

menu #3 - remote start options

Содержание 560XV
























































Результаты поиска

Содержание 560XV

Отзывы:

Похожие инструкции для 560XV

Бренды по названию

Популярные бренды

Directed Electronics 560XV, Руководство по установке

Результаты поиска

Содержание 560XV

Отзывы:

Похожие инструкции для 560XV

Бренды по названию

Популярные бренды