Directed Electronics 560XV Скачать руководство пользователя

Страница: 46 / 55

3-4 PARKING LIGHTS FLASHING/CONSTANT:

In the default setting, the unit will flash the vehicle's parking

lights (if connected) while remote started. The constant setting will turn the parking lights on solid for the entire

run duration.

3-5 CRANK TIME 0.6/0.8/1.0/1.2/1.4/1.6/1.8/2.0/4.0 SECONDS:

If the unit is programmed for no engine

checking or voltage sense, the crank time must be set to the appropriate duration. The default setting is 0.6

second. If a different crank time is desired, select feature 3-5 and select either 0.6 second by using the one-

chirp setting or toggle through the higher settings by using the two-chirp settings.

3-6 VOLTAGE CHECK HI/LOW:

This feature only functions when programmed for voltage sense. Some vehicles

have many accessories, which are turned on when remote started. In these vehicles, the variation of voltage

between the engine off and the car running is very small and the remote start unit may "think" the vehicle has

not started. This can cause the remote start to shut-down after the car has been started. If this happens program

this feature to the LOW position.

3-7 SHORT RUN/TURBO:

When the

and

buttons on the transmitter are pressed simultaneously,

the vehicle will start for the programmed short run time. The factory default is 1 minute.

3-8 ACTIVATION PULSE COUNT:

This allows the system to use 1 or 2 pulses to activate the remote start

sequence.

Note!

1 or 2 pulses on the WHITE/BLUE remote start activation input wire as well as the

button of the remote control.

3-9 2nd IGNITION/2nd ACCESSORY OUTPUT:

This will allow the PINK/WHITE to be used as a 2nd ignition or an

accessory.

3-10 ACCESSORY STATE DURING WAIT-TO-START:

This feature will allow the selection of the accessory output

to be ON or OFF during wait-to-start.

3-11 2nd STATUS OUTPUT:

This feature will allow selection of status ouput or a rear defogger mode that turns

on ten seconds after the vehicle has started. The defogger mode has two selections, latched or pulsed. Latched

mode will only stay on for 10 minutes.

3-12 ANTI-GRIND ON/OFF:

With the anti-grind On (default) the ground-when-armed output will be active during

remote start operation. If accessories such as a voice module or window module are added to the unit, it may

be necessary to program this feature off.

Содержание 560XV
























































Результаты поиска

Содержание 560XV

Отзывы:

Похожие инструкции для 560XV

Бренды по названию

Популярные бренды

Directed Electronics 560XV, Руководство по установке

Результаты поиска

Содержание 560XV

Отзывы:

Похожие инструкции для 560XV

Бренды по названию

Популярные бренды