Directed Electronics 560XV Скачать руководство пользователя

Страница: 19 / 55

Most vehicles use negative door trigger circuits. Connect the green wire to a wire which shows ground when any

door is opened. In vehicles with factory delays on the domelight circuit, there is usually a wire that is unaffected

by the delay circuitry. This wire will report Zone 3.

Inputs shorter than 0.8 seconds will trigger the Warn Away response, while inputs longer than 0.8 seconds will

trigger the full alarm sequence. If installing an optional Directed Electronics dual stage sensor, connect both the

blue and the green wires of the optional sensor to this input. This wire will report Zone 4.

This wire is used in vehicles that have a positive (+) switched dome light circuit. Connect the violet wire to a

wire that shows (+)12V when any door is opened, and ground when the door is closed. This wire will report Zone 3.

H1/7 VIOLET (+) door trigger input, zone 3

H1/6 BLUE (-) multiplex input, zone 4

H1/5 GREEN (-) door trigger input, zone 3

Содержание 560XV
























































Результаты поиска

Содержание 560XV

Отзывы:

Похожие инструкции для 560XV

Бренды по названию

Популярные бренды

Directed Electronics 560XV, Руководство по установке

Результаты поиска

Содержание 560XV

Отзывы:

Похожие инструкции для 560XV

Бренды по названию

Популярные бренды