background image

128-9104

1 of 32

1

FEATURES:

Selectable Ignition Lock and Unlock
Selectable Door Lock/Unlock Output Timing
Safe Start (Requires double push of the start button to engage the remote start function)
On Board Parking Light Relay
Trunk Release Output
Horn Chirp Output With Duration Select
Selectable RF Start Chirp
Panic Mode (Can select to have horn along with parking lights)
Selectable Run Times 5, 10, 15, or 20 Minutes
Selectable Gas or Diesel
Automatic Start Timer (Can be set to start your car automatically at 2 or 4 hour intervals)
4 Negative Pulsed Aux Outputs Before Start, After Start, During Crank, After Shut Down
(To aid installation in many vehicles with factory alarm systems)
Turbo Timer
Dual Stage Shock Sensor
Shock Sensor Shunt During R/S Selectable
Pathway Illumination selection 15 seconds w/lock, unlock, or both

FCC NOTICE

This device complies with part 15 of the FCC rules. Operation of this device is subject to the
following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance voids the users authority to operate this device.

This Remote Start/Alarm System is designed to be used with

Automatic Transmission-Fuel Injection Vehicles Only!

COMPONENTS:

Control Module
1 Four Button LCD Transceiver
1 Four Button RF Transmitter
1 Two Way Antenna/Transceiver
1 “1 X 1.75” Foam Pad
6 Pin Main Power Harness w/Fuses
20 Pin Accessory Harness
2 Pin Door Lock/Unlock Harness

Starter Inhibit Relay & Harness
5 Pin Antenna Receivers Harness
4 Pin Auxiliary Output Harness
Installation/Owners Guide
Dual Stage Magnetic Resonance Shock
Sensor
1 Hood Pin Switch

Model  PA-920C

Installation Manual

Summary of Contents for PA-920C

































Reviews: