Directed Electronics 560XV Скачать руководство пользователя

Страница: 47 / 55

nuisance prevention circuitry

™

NPC™ requires that you change the way you test the system as NPC™ will bypass an input zone for 60 minutes.

If the system “sees” the same zone trigger three times AND the triggers are spaced less than an hour apart, the

system will bypass that input zone for 60 minutes. If that zone does not attempt to trigger the system during

the 60-minute bypass period, the zone’s monitoring will begin again at the end of the hour. If it does attempt

to trigger while bypassed, the 60-minute bypass starts over again.

Disarming and rearming the system does not reset NPC™. The only way to reset NPC™ is for the 60 minutes to

pass, without a trigger, or for the ignition to be turned on. This allows the system to be repeatedly triggered,

disarmed and rearmed, and still allow NPC™ to bypass a faulty zone.

When disarming the system, 5 chirps indicate NPC is activated. The LED will report the zone that has been

bypassed. (See

Diagnostics

section of this guide.)

valet mode

To enter or exit valet mode with the valet/program switch:

Turn the ignition key on and then off.

At anytime during the next 10 seconds, press and release the Valet® switch. Now the Status

LED will light constantly if you have entered Valet® Mode, and go out if you have exited

Valet® Mode.

To enter or exit valet mode with the transmitter:

To enter or exit Valet® Mode with a transmitter:

1. Open any door.

2. Press

on the transmitter.

3. Press .

4. Press

again. You have now entered or exited Valet Mode (verify by checking your status LED).

Содержание 560XV
























































Результаты поиска

Содержание 560XV

Отзывы:

Похожие инструкции для 560XV

Бренды по названию

Популярные бренды

Directed Electronics 560XV, Руководство по установке

Результаты поиска

Содержание 560XV

Отзывы:

Похожие инструкции для 560XV

Бренды по названию

Популярные бренды