Digitus DN-70590 Скачать руководство пользователя страница 39

Страница: 39 / 170

Here are descriptions of every setup items:

User Name (1):

Please input user ID (user name) assigned by your
Internet service provider here.

Password (2):

Please input the password assigned by your Internet
service provider here.

PPTP

Please input the IP address of PPTP gateway

Gateway (3):

assigned by your Internet service provider here.

Connection

Please input the connection ID here, this is

(4):

optional

and you can leave it blank.

MTU (5):

Please input the MTU value of your network connection
here. If you don’t know, you can use default value.

BEZEQ-ISRAEL (6): Setting item ‘BEZEQ-ISRAEL’ is only required to

Check if you’re using the service provided by BEZEQ

network in Israel.

Connection

Please select the connection type of Internet

type (7):

connection you wish to use, please refer to last section
for detailed descriptions.

Idle Time

Please input the idle time out of Internet

Out (8):

connection you wish to use, and refer to last section for
detailed descriptions

When you finish with all settings, please click ‘OK (9); if you want to
go back to previous menu, click ‘Back’.

Содержание DN-70590











































































































































































Результаты поиска

Содержание DN-70590

Отзывы:

Похожие инструкции для DN-70590

Бренды по названию

Популярные бренды

Digitus DN-70590, Руководство пользователя

Результаты поиска

Содержание DN-70590

Отзывы:

Похожие инструкции для DN-70590

Бренды по названию

Популярные бренды