Digitus DN-70590 Скачать руководство пользователя страница 35

Страница: 35 / 170

2-3-2 Setup procedure for ‘Fixed-IP xDSL’:

Here are descriptions of every setup items:

IP address

Please input IP address assigned assigned by your

Service Provider (1): by your service provider.

Subnet Mask (2):

Please input subnet mask assigned by your service
provider

DNS address (3):

Please input the IP address of DNS server provided by
your service provider.

Service Provider

Please input the IP address of DNS server

Gateway Address (4): provided by your service provider.

When you finish with all settings, press ‘OK’ (5); if you want to go
back to previous menu, click ‘Back’.

2-3-3 Setup procedure for ‘PPPoE xDSL’:

1
2
3
4

NOTE: You can choose this Internet connection method if your
service provider assigns a fixed IP address (also know as static
address) to you, and not using DHCP or PPPoE protocol. Please
contact your service provider for further information.

You must use the addresses provided by your Internet service
provider, wrong setting value will cause connection problem.

Содержание DN-70590











































































































































































Результаты поиска

Содержание DN-70590

Отзывы:

Похожие инструкции для DN-70590

Бренды по названию

Популярные бренды

Digitus DN-70590, Руководство пользователя

Результаты поиска

Содержание DN-70590

Отзывы:

Похожие инструкции для DN-70590

Бренды по названию

Популярные бренды