background image

rev 171212

Liberty AV Solutions

11675 Ridgeline Drive

Colorado Springs, CO 80918

800-530-8998

[email protected]

Technical Specifications

Input/Output Connections

LAN

Two (2) 8P8C port (Shielded RJ45)

Power

One (1) 5.5 mm OD, 2.6 mm ID Threaded Barrel

RS232 Port

One (1) 6-pin Removable Terminal Block Connector

Reset Button

One (1) Recessed Microswitch

Supported Control

Supported Baud Rates

9600 (control) and 115200 (debug)

Ethernet

100BaseT

LAN Maximum Distance

100 m (328 ft)

LAN Cable Requirements

Category 5e or greater with TIA/EIA-568B crimp pattern

Chassis and Environmental

Construction

Black Steel

Dimensions (H x W x D)

26 mm x 93.2 mm x 138.7 mm (1.02 in x 3.67 in x 5.46 in)

Operating Temperature

0° to +40° C (+32° to +104° F)

Operating Humidity

20% to 90%, Non-condensing

Storage Temperature

-10° to +60° C (+14° to +140° F)

Storage Humidity

20% to 90%, Non-condensing

Power and Regulatory

Power Input

12V DC 1A or 48V DC PoE (Power over Ethernet)

Power Output (RS232 port)

12V DC 0.5A

Power over Ethernet (PoE) Compat-

ibility

802.3af Alternative B

Power Consumption

4.5 watts (10.5 watts when using 12V on RS232 port)

ESD Protection

8kV air, 4kV contact

Regulatory

FCC, CE, RoHS

Other

Warranty

2 years

Diagnostic Indicators

Status and Power

Included Accessories

Installation Guide, Power Supply, 6-pin Removable Screw 

Terminal

Compatible Encoders

IPEX2001, IPEX5001

Compatible Decoders

IPEX2002, IPEX5002

Содержание IPEXCB





















Отзывы: