DIGITALas D-FORCE600VA Скачать руководство пользователя

Страница: 3 / 24

D-FORCE600VA SLIDING GATE OPERATOR

gates.



The automatic gate operator must be grounded.



Install the gate operator on the inside of the property; DO NOT install

it on the outside of the property where the public has access to it.



Be careful when in close proximity to moving parts where hands or

fingers could be pinched.



Do not allow control devices to be placed so that a person can access

them by reaching through the gate.



In the event of power failure, an emergency release key allows you to

operate the gate manually.



The operator should be switched off before repairing it or opening its

cover.



Please erase and reprogram the transmitter code after installing the

operator.

Make sure the Power supply (AC220V or AC110V) of the gate operator is

suitable for the power supply in your area.

3. Main technical parameters

Type

D-FORCE600VA

D-FORCE600VA U

Power supply

220V, 50Hz

110V, 60Hz

Motor speed

55rpm

66rpm

Rated output power of motor

200W

Содержание D-FORCE600VA

























Результаты поиска

Содержание D-FORCE600VA

Отзывы:

Похожие инструкции для D-FORCE600VA

Бренды по названию

Популярные бренды

DIGITALas D-FORCE600VA, Руководство пользователя

Результаты поиска

Содержание D-FORCE600VA

Отзывы:

Похожие инструкции для D-FORCE600VA

Бренды по названию

Популярные бренды