DIGITALas D-FORCE600VA Скачать руководство пользователя

Страница: 22 / 24

D-FORCE600VA SLIDING GATE OPERATOR

the button is pressed the LED will light.

LED 7 indicate the ‘infrared sensor’ status, if the output

is connected the LED will light.

LED 9 indicate the ‘Loop detector’ status, if the output is

connected the LED will light.

LED 10 indicate the ‘Close limit switch’ status, if the

switch is connected the LED will light.

LED 12 indicate the ‘Open limit switch’ status, if the

switch is connected the LED will light.
All these LED position see the Fig.8

10.

Maintenance



Check the door once a month. The door should be carefully checked

for balance. The door must be in good working order.



We suggest for safety reasons, photocells be used on all gates.



Disconnect from mains supply before replacing bulb.



Be sure to read the entire manual before attempting to perform any

installation or service to the door operator.



Our company reserves the right to change the design and specification

without prior notification.

11.

Troubleshooting

Trouble

Possible causes

Solutions

The door fails to

open and close.

LED display

does not light.

1. Power is OFF

2. Fuse burn

1. Make sure that

power is ON.
2. Replace fuse.

Содержание D-FORCE600VA

























Результаты поиска

Содержание D-FORCE600VA

Отзывы:

Похожие инструкции для D-FORCE600VA

Бренды по названию

Популярные бренды

DIGITALas D-FORCE600VA, Руководство пользователя

Результаты поиска

Содержание D-FORCE600VA

Отзывы:

Похожие инструкции для D-FORCE600VA

Бренды по названию

Популярные бренды