DIGITALas D-FORCE600VA Скачать руководство пользователя

Страница: 23 / 24

D-FORCE600VA SLIDING GATE OPERATOR

The door can

open fails to

close.

1. Infrared beam is
obstructed.

2. Infrared sensor

function is enabling, but

the sensor has not been

installed.

Remove

obstructions.

2. Make sure the

infrared

sensor

function is disabling.

Remote

transmitter does
not work.

1. Battery level may be

low

2. Transmitter code is

lost

1. Replace the battery

inside the transmitter.

2. Reprogram the

transmitter.

The transmitter

operating

distance is too

short.

Battery level may be

low.

Replace battery.

11. Packing list

After receiving the gate operator, you should make an unpack-inspection,

in which you should check whether the product was damaged. If you have

any problem please contact our dealer. You should find the following items

in our standard packing:

No.

Item

Quantit

D-FORCE600VA sliding

gate operator

Содержание D-FORCE600VA

























Результаты поиска

Содержание D-FORCE600VA

Отзывы:

Похожие инструкции для D-FORCE600VA

Бренды по названию

Популярные бренды

DIGITALas D-FORCE600VA, Руководство пользователя

Результаты поиска

Содержание D-FORCE600VA

Отзывы:

Похожие инструкции для D-FORCE600VA

Бренды по названию

Популярные бренды