DIGITALas D-FORCE1400VA Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 23

background image

D-FORCE1400VA SLIDING GATE OPERATOR

4.

Mechanical Installation

The D-FORCE1400VA will handle gate weighting up to 800kg/1400 kg

and up to 14m/20m if the proper installation procedures have been

followed.

The D-FORCE1400VA gate operator operates by forcing a drive rack by a

drive gear. The entire configuration is shown in the diagram below. The

gate operator must be installed on the inside of the gate.

Wall

Switch

Gate operator

Input power

Rack

Sliding gate

Fig.1

Gate preparation
Be sure the gate is properly installed and slides smoothly before installing

the D-FORCE1400VA sliding gate operator. The gate must be plumb, level,

and move freely.

Conduit

In order to protect the cable, use PVC conduit for low voltage power cable
and control wires. Conduit must be preset into the concrete when it is
poured. Wires within the conduit shall be located or protected so that no

4

«
...
2
3
4
5
6
...
»

Содержание D-FORCE1400VA
























Отзывы:

Нет отзывов

Похожие инструкции для D-FORCE1400VA

Бренд: Roger Страницы: 8

Бренд: Chamberlain Страницы: 24

Бренд: Chamberlain Страницы: 40

Бренд: Chamberlain Страницы: 2

Бренд: Overlap Страницы: 22

Бренд: Nice Страницы: 128

Бренд: Becker Страницы: 16

Бренд: Hy-Security Страницы: 32

Бренд: Roger Technology Страницы: 72

Бренд: Beninca Страницы: 24

Бренд: Accessmatic Страницы: 78

CORPORAL II STANDARD Series

Бренд: Raynor Страницы: 44

Бренд: GTO Страницы: 48

Бренд: RAMSET Страницы: 16

Бренд: Accessmatic Страницы: 60

Бренд: Calimet Страницы: 24

Бренд: TMT Страницы: 16

Бренд: Cardale Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды