background image

Net-2000™ Voice Codec Unit 
User’s Manual

 

 

DVSI Confidential Proprietary 

Page iii 

Information – Section 

Safety Instructions 

Safety Precautions 

1.  Read Instructions - All the safety and operating instructions should be read before operating the 

Net-2000™- P25 VCU unit. Failure to exercise reasonable care and to follow all instructions and 
heed all warnings may result in injury to property or to individuals. 

 
2.  Retain Instructions - The safety and operating instructions should be retained for future reference. 
 
3.  Heed Warnings - Adhered to all warnings and cautions on the unit and in the operating 

instructions. 

 
4.  Follow Instructions - All operating and use instructions should be followed. 
 
5.  Water and Moisture - The appliance should not be used near water - for example, near a 

washbowl, sink, laundry tub, or in a wet or damp location.  Moisture may form inside the unit it is 
brought from cool surroundings into a warm room or if the room temperature suddenly rises. To 
prevent this, let the Net-2000™- P25 VCU  unit stand in its new surroundings for about an hour 
before switching it on, or make sure the room temperature rises gradually. Condensation may also 
form if the unit is exposed to the breeze from an air conditioner.  In these situations, change the 
location of the Net-2000™- P25 VCU . 

 
6.  Carts and Stands - The Net-2000™- P25 VCU  unit should be used only with a cart or stand that is 

suitable for the units size and weight. The unit and cart combination should be moved with care. 
Quick stops, excessive force, and uneven surfaces may cause the cart to overturn. 

 
7.  Wall or Ceiling Mounting - The Net-2000™- P25 VCU unit is not intended to be mounted to a wall 

or the ceiling. 

 
8.  Ventilation - The Net-2000™- P25 VCU  unit should be situated so that its location or position does 

not interfere with proper ventilation and air circulation around the unit.  For example, the unit 
should also not be placed in a built-in installation, such as an sealed cabinet or bookcase that may 
impede the flow of air around the unit. 

 
9.  Heat -  The Net-2000™- P25 VCU  unit should be situated away from heat sources such as 

radiators, heat registers, ovens, or other appliances (including amplifiers) that produce heat. 

 
10.  Power Sources -  The Unit should be connected to an AC power source only of the type described 

in the operating instructions or as marked on the Net-2000™- P25 VCU  unit.  The Net-2000™- 
P25 VCU  unit uses AC voltages which can cause death or serious injury if used improperly.  
Extreme care must be taken when connecting or disconnecting from power sources and in no 
event should the user remove the cover or back of the unit. 

 
11.  Grounding and Polarization - Precautions should be taken to insure that the grounding or 

polarization means of the Net-2000™- P25 VCU unit is not defeated. 

 
12.  Power-Cord Protection -  Power-supply cords should be routed so that they are not likely to be 

walked on or pinched by items placed upon or against them. Pay particular attention to cords at 
plugs, convenience receptacles, and the point where they connect to the Net-2000™- P25 VCU  
unit.  Handle the power-cord by the plug.  Do not pull out the plug by tugging the cord. 

 
13.  Cleaning -  Unplug the Net-2000™- P25 VCU unit from the AC power source before cleaning.  The 

unit should be cleaned only with a polishing cloth or soft dry cloth.  Never clean the unit with 
furniture wax, benzene, insecticides, or other volatile liquids. 

 
14.  Nonuse Periods -  The AC power cord of the Net-2000™- P25 VCU  unit should be unplugged 

from the wall outlet when left unused for long periods of time. 

Содержание Net-2000-P25

















































Отзывы: