manualshive.com logo in svg

Digital Equipment DLE28-MA, Руководство пользователя, Страница: 168 / 200

Поделиться
Скачать
Digital Equipment DLE28-MA Скачать руководство пользователя страница 168

Chapter 5: Local Management

5-110

DLE28-MA User’s Guide

bridge:

Syntax:

bridge [ENABLE/DISABLE] [IFNUM/ALL]

Description:

The bridge command allows each bridge port to 
be enabled or disabled at the user’s request, 
either one at a time or all at once. Specifying a 
single interface number will affect the bridging 
status of that interface, while specifying ALL 
will affect every interface.

Options:

Not Applicable

Example:

defroute:

Syntax:

defroute [interface number] [IP address]

Description:

The defroute command allows the user to view, 
set or delete the default IP route to a managed 
device through the specified interface.

-> arp -a

# Interface
# (SonicInt)
# (SonicInt)
# (SonicInt)
# (SonicInt)

Network Address
122.144.40.111
122.144.48.109
122.144.52.68
122.144.21.43

Physical Address
00.00.0e.12.3c.04
00.00.0e.f3.3d.14
00.00.0e.12.3c.04
00.00.0e.03.1d.3c

Media Type
3(dynamic)
3(dynamic)
3(dynamic)
3(dynamic)

-> arp -d 1 122.144.52.68

-> arp -s 1 22.44.2.3 00:00:0e:03:1d:3c

051467

-> arp -f

-> bridge disable all

-> bridge enable 1

051468

-> bridge disable 1

Содержание DLE28-MA









































































































































































































Отзывы:

Нет отзывов