Digital Equipment DLE28-MA Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 200

background image

Broadcast Suppression Screen

DLE28-MA User’s Guide

5-93

5.26

BROADCAST SUPPRESSION SCREEN

The Broadcast Suppression screen, Figure 5-31, allows the user to set a
desired limit of receive broadcast frames that are switched out to the other
ports.

To access the Broadcast Suppression screen from the Module Specific
Configuration screen, use the arrow keys to highlight the BROADCAST
SUPPRESSION menu item and press ENTER. The Broadcast
Suppression screen displays.

Figure 5-31

Broadcast Suppression Screen

The Broadcast Suppression screen may not be available if the
operational mode of the module has been set to 802.1Q
SWITCHING. Refer to your Release Notes to see what
operational modes support Broadcast Suppression. Refer to
Section 5.15.9, Setting the Operational Mode, for instructions
on configuring the operational mode of the module.

Any broadcast frames received above the desired threshold will
be dropped.

Firmware Revision: XX.XX.XX

Broadcast Suppression

LKG-10830-98F

BOOTPROM Revision: XX.XX.XX

PORT #

1

2

3

4

5

6

7

8

9

10

11

12

Time Since Peak

999:23:59

999:23:59

999:23:59

999:23:59

999:23:59

999:23:59

999:23:59

999:23:59

999:23:59

999:23:59

999:23:59

999:23:59

Peak Rate

150000

150000

150000

150000

150000

150000

150000

150000

150000

150000

150000

150000

Threshold

150000

150000

150000

150000

150000

150000

150000

150000

150000

150000

150000

150000

Module Type: DLE28-MA

Slot Number: X

MS 700 LOCAL MANAGEMENT

Event Message Line

Total RX

12345678910

12345678910

12345678910

12345678910

12345678910

12345678910

12345678910

12345678910

12345678910

12345678910

12345678910

12345678910

Reset Peak

[NO]

[NO]

[NO]

[NO]

[NO]

[NO]

[NO]

[NO]

[NO]

[NO]

[NO]

[NO]

RETURN

RETURN

SAVE

[13-24]

EXIT

«
...
149
150
151
152
153
...
»

Содержание DLE28-MA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DLE28-MA

Бренд: TC-Helicon Страницы: 2

Бренд: Amperes Страницы: 8

Бренд: NETGEAR Страницы: 84

IBOX-BAC Series

Бренд: IntesisBox Страницы: 2

WRT54GR - Wireless-G Broadband Router

Бренд: Linksys Страницы: 81

Бренд: Kanguru Страницы: 13

Бренд: Glacier Страницы: 2

Бренд: WABCO Страницы: 29

SmartSwitch 8-slot

Бренд: Cabletron Systems Страницы: 150

Бренд: ZyXEL Communications Страницы: 170

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: Technics Страницы: 20

Бренд: IBM Страницы: 64

Acme Packet 3900

Бренд: Oracle Страницы: 70

Бренд: ADTRAN Страницы: 2

Бренд: Aim Страницы: 35

Бренд: Freescale Semiconductor Страницы: 124

Бренд: Atlantis Land Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды