Digital Equipment DLE28-MA Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 200

background image

Chapter 5: Local Management

5-46

DLE28-MA User’s Guide

ENTERED”. Local Management does not alter the current value, but
it does refresh the Subnet Mask field with the previous value.

4.

Use the arrow keys to highlight the SAVE command, then press
ENTER. The warning screen shown back in Figure 5-18 displays.

5.

Use the arrow keys to highlight the YES command and press ENTER.
The changes are saved and the module reboots

5.15.3

Setting the Default Gateway

If the SNMP management station is located on a different IP subnet than
the DLE28-MA, a default gateway must be specified. When an SNMP
Trap is generated, the DLE28-MA sends the Trap to the default gateway.
To set the default gateway, perform the following steps:

1.

Use the arrow keys to highlight the Default Gateway field.

2.

Enter the IP address of the default gateway using the DDN format.

For example: 134.141.79.121

3.

Press ENTER. If the default gateway entered is a valid format, the
cursor returns to the beginning of the Default Gateway field. If the
entry is not valid, the Event Message Line displays “INVALID
DEFAULT GATEWAY OR FORMAT ENTERED”. Local
Management does not alter the current value, but it does refresh the
Default Gateway field with the previous value.

4.

Use the arrow keys to highlight the SAVE command.

5.

Press ENTER. The Event Message Line at the top of the screen
displays “SAVED OK”.

5.15.4

Setting the TFTP Gateway IP Address

If the network TFTP server is located on a different IP subnet than the
DLE28-MA, a Gateway IP address should be specified. To set the TFTP
Gateway IP address, perform the following steps:

«
...
102
103
104
105
106
...
»

Содержание DLE28-MA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DLE28-MA

Бренд: EAW Страницы: 10

Бренд: Panasonic Страницы: 4

Бренд: Abocom Страницы: 1

Бренд: Patton electronics Страницы: 8

Бренд: D-Link Страницы: 176

Бренд: IOtech Страницы: 16

Through Hole Power Inductors 1411

Бренд: Delta Electronics Страницы: 1

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: DIGIWEB Страницы: 16

Husky HMG-1648EP

Бренд: Ethernet Direct Страницы: 16

Бренд: IBM Страницы: 64

Бренд: ICS ELECTRONICS Страницы: 4

Бренд: Deliberant Страницы: 16

MS-96 Vial Reader

Бренд: Microscan Страницы: 67

Бренд: ADTRAN Страницы: 2

Бренд: Aim Страницы: 35

Бренд: TRENDnet Страницы: 57

Бренд: IceManCooler Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды