Digital Equipment DLE28-MA Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 200

background image

Chapter 5: Local Management

5-82

DLE28-MA User’s Guide

Advertised Ability (Selectable)

During auto-negotiation, the DELTX-UI “tells” the device at the other end
of the segment what its capabilities are. The capabilities of a port (25 or
26) with a DELTX-UI installed are 10BASE-T, 10BASE-TFD (full
duplex mode), 100BASE-TX and 100BASE-TXFD (full duplex mode). In
normal operation, with all capabilities enabled, the DELTX-UI
“advertises” that it has the ability to operate in any mode. The Network
Manager may choose to set up the port so that only a portion of the
available capabilities are advertised and the others are disabled. For
example, only 100BASE-TX and 100BASE-TXFD might be enabled so
that only devices that operate at 100 Mbps can communicate with that
port. Section 5.23.5 describes how to enable or disable advertised modes.

5.23.1

Configuring a DELFX-UI or DELF3-UI

When a DELFX-UI or DELF3-UI is installed in port 25 or 26, it must be
manually set to operate in the same technology as the device at the other
end of the connected segment. Section 5.23.2 provides instructions for
manually configuring the port with a DELFX-UI or DELF3-UI interface.

5.23.2

Setting the DELFX-UI and DELF3-UI
Operational Mode

Use the Desired Oper. Mode field to set the active technology. This field
toggles between 100Base-FX and 100Base-FXFD (full duplex). To set the
active technology through Local Management, proceed as follows:

1.

Use the arrow keys to highlight the Desired Oper. Mode field.

2.

Use the SPACE bar to select 100Base-FX or 100Base-FXFD (full
duplex).

3.

Press ENTER. The port now operates in the chosen mode.

4.

Use the arrow keys to highlight the SAVE command. Press ENTER.
The message “SAVED OK” displays and Local Management saves
the changes to memory.

«
...
138
139
140
141
142
...
»

Содержание DLE28-MA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DLE28-MA

Бренд: C4i Страницы: 8

Бренд: IBM Страницы: 248

Бренд: XESS Страницы: 23

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

Бренд: Allnet Страницы: 12

Бренд: Telebyte Страницы: 19

Бренд: Justec Страницы: 61

PARTNER PC CARD

Бренд: Avaya Страницы: 4

Бренд: Paradyne Страницы: 6

Бренд: SeaLevel Страницы: 34

Бренд: IFM Electronic Страницы: 14

Бренд: Patton electronics Страницы: 145

Бренд: FOR-A Страницы: 2

EK-FC750 GTX Series

Бренд: ekwb Страницы: 2

Бренд: Hawking Страницы: 21

TGXPS-1080-M12-MV Series

Бренд: ORiNG Страницы: 2

Бренд: Alesis Страницы: 11

CyberPower RMCARD201

Бренд: CyberPower Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды