5. Press B to reset and be ready for the next race, as shown in Fig. 7. The counter at the top left corner displays the memory left for
further races.
6. Further races can be recorded by pressing A and B buttons as above.
Since 5 memories are used for memorizing the date and number of the race, the memory left will be 1993 as shown below.
TIMER OPERATION:
1. Press C button until the stopwatch goes to the TIMER mode. The display is as shown in Fig.18. The top row is the display for the
1st timer and the middle row is the display for the 2nd timer.
2. Press and hold B button for 2 seconds to go into the SET TIMER mode with the hour digit of the 1
st
timer blinking.
3. Press A button to set to desired hour for countdown.
4. Press B to go to the first digit in minutes and press A to set minutes.
5. Similarly by using B and A buttons the desired countdown times for the 1st and 2nd timers can be set.
6. Pressing C button once any time during this TIMER setting sequence will complete the setting and the timer is ready to start upon
pressing the A button.
7. Press A to s
tart countdown with the “1 ” at the top right corner blinking and the timer setting counting down. When the 1st timer
approaches zero, the timer gives 4 beeps and the 2nd timer starts counting down immediately. When the 2nd timer approaches zero,
it gives 2 beeps and the 4 digit counter at the lowest row advances by 1 automatically.
8. At any time during countdown pressing A will stop counting.
If only the 1st timer is set the timer is used as an ordinary countdown timer and will give 5 times 4 beeps when the set time is up. The
4 digit counter also advances by 1 automatically when the timer reaches zero.
STROKE / FREQUENCE BASE 3 ;
1. Press the button
C
to go into « chronograph mode ».
2. Press B during few seconds to go into « speed mode » (cf fig.14).
3. Scroll with the button
B
.
4. Select the numbers with the button
A
. The distance has to be set up on « 180 » (0180.000) and the time unit on « seconds »
(SEC).
Then, press
C
to confirm.
5. Start the « chronograph mode » with the button
A
. After the third stroke
only,
press
A
again. The line in the middle indicates the
number of strokes per minute.
DATA STORED RECALL:
1. Press D to recall data stored. The display which we call the RACE RECORD is as shown in Fig. 8.
2. The display shows the date in which the race was recorded and MCH-001 (MSP for SPEED mode) stands for the first race
3. Recorded in LAP/SPLIT mode at that date.
4. Press D again to recall the 1st LAP data, as shown in Fig.9.
5. Press D to recall the 2nd LAP data.
6. Press D again shows the stopped time
7. Press D again to show the average LAP time
8. Press D again to show the Best LAP time.
9. The AVERAGE calculation and BEST record do not take into account the last section of time before STOP. Therefore, in order for
the stopwatch to keep track of the average and best records of all laps, always use the B button until the end of the race.
10. Pressing D again will go to the next race records or return to the 1st race records (if there is no further race).
MEMORY USED UP:
You have the possibility to clear the races one by one, or to clear all. From the chronograph mode (time display must be put to zero),
press the D button to accede to data stored.
1.
Clear the races one by one
:
Choose the race you want to clear and press B button (race number in the right down corner). Press and hold A button when the
stopwatch is displaying the RACE RECORDS will clear the memories in that race record (when the contents in this race record are
cleared the display will show
“CLEARED”
and sounds a long beep, if A is released before ED appears. Repeat the operation to clear
races one by one.
2. Clear all races:
Press A button during some seconds.
«
CLEAR
», «
CLEARED
», «
ALL CLEAR
», «
ALL CLEARED
» will appear successively.
“ALL CLEARED” appears when all data are cleared. The display comes back to the chronograph mode (fig.2)
When all the memories have been used the 4 digit LAP counter at the top left corner will start blinking to indicate all memories have
been used up. All further LAP memories will not be recorded in the memory unless some memories are cleared as previously
indicated. When there is no memory left pressing A to start a race will sound 3 short beeps.
Do not leave the stopwatch running if not in use as that drains a higher power from the battery.
UPLOAD MODE:
1. In Fig. 20 press D button once will switch to UPLOAD MODE.
2. Pressing A button will UPLOAD ALL recorded memories to computer (if computer is connected). When the stopwatch is in the
process of uploading, an indicator moves from right to left. When upload is complete UPLOAD END is displayed.
3. Press D button to return to PRINT MODE.
4. Pressing B at the UPLOAD ALL mode will go to the UPLOAD RACE mode with display.
5. Pressing A in this mode will only upload the memories in this race.
6. Press B to select particular race to upload.
7. Pressing C any time during this uploading process will stop printing immediately.
8. If the chronograph is not reset (i.e. still running or stopped), it will not be possible to upload and the display will show UPLOAD 0,
there will not be any action upon pressing A or B.
