manualshive.com logo in svg

Digi One TS W, Руководство пользователя

Поделиться
Скачать
Digi One TS W Скачать руководство пользователя страница 76

76

Chapter 18 

  

Configuring Power Over the Serial Ports

 

2. Close the device unit enclosure.

RI Power Out

Ring Indicator (RI) power out is available on all ports. The total power 
budget for this feature is one (1) watt not to exceed 5 volts @ up to 200mA 
on any single port. The following procedure assumes the unit will only be 
used for RI power out.

1. Set the port DIP switches to the following places: switch 1 and 3 are up 

and 2 and 4 are down (see "Serial Power Table" on page 77 for 
illustration).

2. Enable the RI power through the web interface. 

3. Connect power supply with the barrel-connector power supply provided 

with the device or use powered Ethernet.

Note:

If the unit will be used with RI power in (port 1 only), set the jumper to the 
following setting:
P-6 jumper on pins 1and 2
and do not use an external power source. Port 1 cannot be used for both 
power in and power out. 

Configuring DTR Power

Power Out 

Data Terminal Ready (DTR) power out is the factory default on the Digi 
device server. Total power budget for this feature is one watt not to exceed 
9 volts @ up to 100mA to any single port. 

1. Set the port DIP switches to EIA 232 (switch 1 is up, 2,3, and 4 are 

down) to enable DTR power.

2. Open the port and set DTR high.

If you are having trouble with your unit after using the Power over port 
feature, you may have tripped the circuit breaker in the unit. You can 
identify this by the RI or DTR signal indicators found in the System 
Information under Administration on the main menu in the web interface.  
Click the port number using serial power. (Remember serial power out is 
unavailable if the MEI settings are not 232.)

Under serial power will be a message if the breaker is tripped. Follow the 

Note Here are the pins to 

verify the jumper 
position. The default 
position has the 
jumper on the two pins 
furthest from the edge. 
DO NOT MOVE THE 
JUMPER FROM THE 
DEFAULT UNLESS 
USING RI POWER IN.

Содержание One TS W





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды