manualshive.com logo in svg

Digi One TS W, Руководство пользователя

Поделиться
Скачать
Digi One TS W Скачать руководство пользователя страница 63

Chapter 13  Configuring the Digi Device for IA (Industrial Automation)

 63

Configuring Modbus

Modbus is a protocol that defines how devices in an industrial automation 
(IA) environment communicate. It specifies that a controlling unit, called a 
master, manages one or more units, called slaves. The protocol specifies 
that only the master may initiate communication. Slaves may only respond. 

The protocol defines the structure of Modbus messages, determines how 
the master requests information from the slave or specifies an action for 
the slave to take, defines how the slave is to respond, specifies addressing 
conventions, and deals with many of the other details required for 
communication to occur. Modbus defines two encoding schemes, Modbus 
ASCII and Modbus RTU. Each Modbus device uses one or the other.

Designed to function over a serial communication cable, Modbus has been 
extended in recent years to function over an Ethernet network using 
Modbus/TCP, which defines a method of encapsulating Modbus ASCII or 
Modbus RTU messages in IP packets for transport over the network. 

The extermely flexible Digi implementation includes support for Modbus 
ASCII, Modbus RTU, Modbus/TCP, and two other methods of transport 
over a network, TCP socket and UDP socket communication. The 
implementation enables multiple network-based masters to concurrently 
initiate communication with serial-based slaves using any of the supported 
network protocols.

Modbus Configuration Procedure

Use the setia command from the  See the Digi One/PortServer TS 
Command Reference for information.

•

Configure the serial port for the serial communication parameters 
(baud rate, data bits, parity and stop bits) required by the connected 
IA device.

•

Choose Modbus ASCII or Modbus RTU as the serial port protocol, 
depending on the requirements of the IA device connected to the 
port.

•

If you configure the port for a slave, you do not have to configure a 
network-based master. Communication with the master just works. 
(If the master is connected to a serial port, it must be configured, 
however.)

•

If you configure a port for a master and the slaves are located on the 
network, TCP sockets, UDP sockets, and Modbus/TCP are all sup-
ported. Use the protocol required by the master.

Configuring the User-Defined Protocol

Digi One\PortServer TS 2/4 MEI devices support what Digi calls the “user-
defined” protocol, which is any IA serial-port protocol with the following 
attributes:

Chapter 13

C o n f i g u r i n g   t h e   D i g i   D e v i c e   f o r   I A

( I n d u s t r i a l   A u t o m a t i o n )

Содержание One TS W





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды