manualshive.com logo in svg

Digi One TS W, Руководство пользователя

Поделиться
Скачать
Digi One TS W Скачать руководство пользователя страница 75

Chapter 18  Configuring Power Over the Serial Ports

 75

Serial Power Feature

The Serial Power feature available for the Digi One TS, PortServer TS 2 
MEI, and PortServer TS 4 MEI allows the Digi device to power a serial 
device (power out) or use a serial device to power the Digi device (power 
in). The advantage of this feature is to eliminate an external power supply. 

Power out is available on all ports through Ring Indicator (RI) or Data 
Terminal Ready (DTR). Power in is available only through RI and only on 
port one (1). The Serial Power feature is active on a specific port when that 
port is configured for RS 232 operation.

•

The power out budget equals one (1) watt (the total amount of 
power available). The available power can be divided in any combi-
nation between the ports but the following rules must be observed:

— RI = 5 volts @ up to 200 mA (max)

— DTR = 9 volts @ up to 100 mA (max)

— You may use DTR or RI as the source of power (power out) on 

any port but you may not use both DTR and RI on the same port.

•

Pinout information

— RI is pin 1

— DTR is pin 9

•

RI signaling is lost when the pin is used for power

Configuring RI Power

RI Power In

Ring Indicator (RI) power in accepts power into the Digi device server only 
on port one. Power in is available using the RI pin. The Digi device requires 
power in the range of 9-30 VDC @ 525mA (max). Ports 2, 3, and 4 can still 
supply power to a serial device through the RI or DTR pins for each port. 
When using power in through the RI, the external power supplies (both 
powered Ethernet and the barrel connector power supply) are inoperative. 
Altpin will not work for RI power in.

1. Open the device unit enclosure and move the black jumper to the 

following settings:
P-6 jumper on pins 1 and 2

Chapter 18

C o n f i g u r i n g   P o w e r   O v e r   t h e   S e r i a l   P o r t s

Note:

When the jumper is placed correctly for 
power in, the jumper will set on the pins 
closest to the edge of the board. The left 
arrow indicates the open pin and the right 
arrow is pointing to the jumper.

Содержание One TS W





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды