Digi One TS W Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 84

Digi One TS W Скачать руководство пользователя страница 39

Chapter 9

Modem Emulation

39

ATXn

Accepted but ignored.

OK n=0 to 3
ERROR
Otherwise

ATYn

Accepted but ignored.

OK n=0 or 1
ERROR
Otherwise

ATZn

Accepted but ignored. (Soft Reset and restore Profile).

OK n=0 or 1
ERROR
Otherwise

AT&Cn

DCD Option. The Digi Device Server controls the DCD output in accor-
dance with the parameter supplied. The parameter value, if valid is written
to S21 bit 5.

&C0 DCD remains ON at all times.

&C1 DCD follows the state of the connection

OK n=0 or 1
ERROR
Otherwise

AT&Dn

DTR Option. This command interprets the ON to OFF transition of the DTR
signal from the DTE in accordance with the parameter supplied. The param-
eter value, if valid, is written to S21 bits 3 and 4. Also see S25.

&D0 -DTR is ignored (assumed ON). Allows operation with DTEs which
do not provide DSR.

&D1DTR drop is interpreted by the modem as if the asynchronous escape
sequence had been entered. The modem returns to asynchronous com-
mand state without disconnecting.

&D2DTR drop causes the modem to hang up. Auto-answer is inhibited.
(Default.)

&D3DTR drop causes the modem to perform a soft reset as if the Z com-
mand were received. The &Y setting determines which profile is loaded.

OK n=0 to 3
ERROR
Otherwise

AT&Fn

Restore Factory Configuration (Profile)

The Device Server loads the factory default configuration (profile). The fac-
tory defaults are identified for each command and in the S-Register descrip-
tions. A configuration (profile) consists of a subset of S-Registers.

&F0Restore factory configuration 0.

&F1Restore factory configuration 1.

OK n=0 or 1
ERROR
Otherwise

AT&Jn

Accepted but ignored.

OK n=0 or 1
ERROR
Otherwise

AT&Gn

Accepted but ignored.

OK n=0 or 1
ERROR
Otherwise

AT&Jn

Accepted but ignored.

OK n=0 or 1
ERROR Other-
wise

AT&Kn

Flow control. This command defines the DTE/DCE flow control mechanism.
The parameter value, if valid, is written to S39 bits 0, 1, and 2.

&K0 Disables flow control

&K3 Enables RTS/CTS flow control (Default)

&K4 Enables XON/XOFF flow control

&K5 Enables transparent XON/XOFF flow control

&K6 Enables both RTS/CTS and XON/XOFF flow control.

OK n=0,3,4,5,or 6
ERROR
Otherwise

AT&Ln

Accepted but ignored.

OK n=0, 1, 2
ERROR
Otherwise

AT

Command

Function

Result

Code

«
...
37
38
39
40
41
...
»

Содержание One TS W





















































































Отзывы:

Нет отзывов