Dick SM-200 TE Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 76

Dick SM-200 TE Скачать руководство пользователя страница 48

SM-200 TE Grinding and Honing Machine

48

Machining Workpieces

9

9. Machining Workpieces

9.1

Sharpening machine knives

Grind the machine knife according to the angle specified by the
knife manufacturer. Adjust the angle by lifting and lowering the
grinding arm and the grinding angle device.

9.2

Clamping and unclamping knives in grinding plates

Clamp the machine knife in a grinding plate in order to grind it. The
grinding plate must be a precise fit for the knife. The grinding plate
is mounted on the double grinding arm, see chapter “Clamping the
grinding plate”, page 43.

1

Place the double grinding arm in the support facing backwards.

2

Open the grinding plate clamping device.

3

Place the machine knife in the grinding plate.

4

Close the grinding plate clamping device.

WARNING

Machine knives have a sharp cutting edge. They could cause
serious injuries.

• Wear cut-resistant gloves when working with knives.
• Work with due care and attention.

NOTE

The grinding process removes material on the knife. Grinding can
cause the knives in a cutter set to have different weights. The cut-
ter shows an imbalance after the knife has been mounted. The dif-
ferent weight of the knives can be balanced on the grinding and
honing machine. Please follow the instructions of the machine
manufacturer. We recommend grinding to ±5 g if no information is
available.

NOTE

Knives can be quickly resharpened on the SM-200 TE grinding
and honing machine with minimal wear with the special UB3F /-XL
belt grinding device accessory.

«
...
46
47
48
49
50
...
»

Содержание SM-200 TE













































































Отзывы:

Нет отзывов