Diamond SmartLyte Скачать руководство пользователя страница 56

Страница: 56 / 81

5 Maintenance and Troubleshooting

ECO 9085 SOP05-5038F Rev.05 Effective Date: 12/06/18 Page 56 of 81

CONDITIONER NOT FOUND

When the conditioning cycle has been initiated, the analyzer checks for proper aspiration

of the conditioning solution using the sample sensor. If the solution is not detected in the

proper time, this error message will be displayed.

Possible causes and remedies:

•

Ensure that a sufficient volume of conditioning solution is presented for aspiration and no air

bubbles are present as solution is aspirated.

•

Check to ensure that the solution is being properly aspirated through the sampling

mechanism. The sample path must be free of leaks or clots.

•

Verify that sample sensor is correctly plugged in and perform the CHECK SAMPLE SENSOR

to verify its proper operation.

•

Check pump tubing and replace as necessary to ensure correct pump rate.

INTERFACE CHECK ERROR

This message is displayed only during the ACTIVATE INTERFACE. Pins 2 and 3 must

be shorted together to perform the ACTIVATE INTERFACE. Make sure that the pins are

not shorted to chassis ground.

Possible cause and remedy:

•

Call Product Support

PRINTER JAM OR DEFECT

This message is displayed when the printer head is jammed and tries to print. It is a

temporary message that is displayed for 2 seconds and then sample results are displayed.

To clear paper jam remove printer from the analyzer and remove jammed paper. Replace

printer and retry. The printer can be removed by grasping the rear edge of the printer

assembly and pulling it to the front. The printer can be removed with the Analyzer power

on. To free up jammed paper, turn the small gears on the left side of the printer module.

Содержание SmartLyte


















































































Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды

Diamond SmartLyte, Руководство по обслуживанию

Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды