manualshive.com logo in svg

Diamond SmartLyte, Руководство по обслуживанию

Поделиться
Скачать
Diamond SmartLyte Скачать руководство пользователя страница 3

 

                                                                            

ECO 9085 SOP05-5038F Rev.05 Effective Date: 12/06/18  Page 3 of 81

 

Important Information! 

 

This Service Manual contains important warnings and safety information to be observed by the user.  

 
This instrument is only intended for one area of application which is described in the instructions. The 

most important prerequisites for application, operation and safety, are explained to ensure smooth 

operation. No warranty or liability claims will be covered if the instrument is applied in areas other 

than those described or if the necessary prerequi

sites and safety measures are not observed.  

The instrument is only to be operated by qualified personnel capable of serving these prerequisites.  

Only accessories and supplies either delivered by or approved by DIAMOND are to be used with the 

instrument.  

Due to the operating principle of the instrument, analytical accuracy not only depends on correct 
operation and function, but also upon a variety of external influences beyond the manufacturer’s 
control. Therefore, the check results from this instrument must be carefully examined by an expert, 
before further measures are taken based on the analytical results.  

Instrument adjustment and maintenance with removed covers and connected power mains are only to 
be performed by a qualified technician who is aware of the dangers involved.  

Instrument repairs are only to be performed by the manufacturer or qualified service personnel.  

 

For a detailed service training video for your SmartLyte Analyzer, please visit:

 

http://www.diamonddiagnostics.com/video/video_SmartLyte.htm

  

 

 
Symbol 

Explanation 

Attention symbol -  Refer to the Operator's Manual or Service Manual for further 
instructions. This symbol is located on the 

inside of the instrument.  

Type B instrument symbol - An instrument of the B type falls under safety 
categories I, II, or III, or has an internal power supply providing the required 
insulation against discharge current and reliable ground connections.  

 

Important Information! 

Содержание SmartLyte


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды