Diamond SmartLyte Скачать руководство пользователя страница 55

Страница: 55 / 81

5 Maintenance and Troubleshooting

ECO 9085 SOP05-5038F Rev.05 Effective Date: 12/06/18 Page 55 of 81

SHUT DOOR

This message occurs when either of two conditions exists.

Sample door is not closed within 20 seconds after samples are in place.

Sample door has been opened and no sample is detected within 20 seconds.

Possible causes and remedies:

•

Close sample door within the time allowed.

•

Check needle mechanism light gate.

•

Check whether sample sensor is plugged in.

SAMPLE NOT FOUND

This message is displayed when any of the following conditions occur:

During sampling, either a bubble in the sample is detected or the sample size is smaller than

the minimum sample required.

The sample door is opened and no sample is fed into the analyzer.

Sample door is not closed within 20 seconds after sample is detected.

Possible causes and remedies:

•

Check whether the sample sensor is plugged in and perform CHECK SAMPLE

SENSOR to verify that it operates correctly.

•

Check sample draw and look for clots or leaks in the sampling system.

CLEANING SOLUTION NOT FOUND

When the cleaning cycle has been initiated, the analyzer checks for proper aspiration of

the cleaning solution using the sample sensor. If solution is not detected in the proper

time, above error message will be displayed.

Possible causes and remedies:

•

Ensure that a sufficient volume of cleaning solution is presented for aspiration and no air

bubbles are present as solution is aspirated.

•

Check to ensure that the solution is being aspirated through the sampling mechanism

correctly. The sample path must be free of leaks or clots.

•

Verify that sample sensor is properly plugged in and perform the CHECK SAMPLE

SENSOR to verify the correct operation of the sample sensor.

•

Check pump tubing and replace as necessary to ensure a correct pump rate.

Содержание SmartLyte


















































































Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды

Diamond SmartLyte, Руководство по обслуживанию

Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды