S Series Shelter
Operation & Maintenance
95310-02
2-5
DHS Systems, LLC
This document contains information proprietary to DHS Systems LLC and is intended solely for use by its customers. No portion of this document may
be reproduced for release to a third party without written consent from DHS Systems LLC
.
d)
If deploying a “T” Model, finish attaching the Boot to the Shelter by securing the remaining Velcro along both
sides.
•
Return the Push Poles to the Transport Bag. Make sure all cinch belts and the Repair Kit is also in the bag.
Stow the Transport Bag so that it is available for packing and storing.
•
Locate the skirt on the interior liner. Detach skirts from the tabs and lay the skirts flat on ground cover. The
Velcro on the ground cover and the skirt should form a continuous band around the inside of the Shelter. If
the skirt is not attached to the tabs and is underneath the wall, the wall must be raised. To lift the wall and pull
the skirt from under the wall, use the Arms & Hands method described above (2-b).
•
Bring in the fabric floor and orient it to the Shelter with the stenciled side face up.
•
Fold the sides and ends over to expose the Velcro strips.
•
Locate a green plastic hook on the underside of the floor.
•
Attach the hook to the looped keeper at ground level.
•
Working around the base of the Shelter, attach the remaining hooks to the looped keepers while securing the
inner line of Velcro on the floor to the Velcro on the skirt.
•
If the hook does not reach, DO NOT PULL ON THE LOOPED KEEPER. To correct this situation and make
the walls vertical;
e)
Position two people in the doorways at both ends of the wall.
f)
Lift the wall in unison by placing one hand on the exterior looped keeper with the wind line and the other hand on
the corresponding interior looped keeper.
g)
Push the wall inward until the wall is vertical.
h)
Attach the Velcro on the perimeter of the floor to the Velcro at the base of the interior wall.
i)
Verify that the Velcro at the doorway of the floor is attached to the Velcro on the ground cover.
j)
When booting a “T” model to a vehicle, back the vehicle into the center of the “T” end.
k)
Place the elastic part of the boot over the vehicle.
008.01 Installing Vestibule Curtains
The S Series Shelter comes with one Vestibule Curtain to create an entryway at either end of the Shelter to maintain
blackout conditions during ingress/egress without turning off the Shelter lights. It also helps maintain an even temperature
within the Shelter when heating and cooling.
1.
Remove from the Storage Bag.
2.
Locate the hooks on the top of the Vestibule Curtain.
3.
Place the hooks on the corresponding looped keepers
4.
Secure the Velcro strip on the Vestibule Curtain to the Velcro between the openings of the interior door.
009.01 Installing Face Plate Curtains
1.
Remove the face plate curtain from the Storage Bag and locate the six (6) plastic hooks sewn to the connector strip.
2.
Starting with the two hooks in the center, begin attaching the hooks to the interior looped keepers on the ceiling of the
“T” side. Be sure that the white side of the curtain faces the interior of the Shelter.
3.
Use the connector strip as a guide, work along the sides of the curtain, attaching the hooks to the looped keepers.
4.
Once all plastic hooks are secured, match the connector strip on the face plate curtain to the Velcro strip on the Shelter.
5.
After the face plate curtain is secured, both sides of the face plate curtain can be rolled back and held in place using the
hook located above the window and the hook located at ground level.
Содержание DRASH S Series
Страница 8: ...THIS PAGE INTENTIONALLY BLANK...
