DFI PT800-AL страница 109 Скачать руководство пользователя

Страница: 109 / 118

108

Using the Suspend to RAM Function

B.1 Using the Suspend to RAM Function

If you are using the Windows

98 operating system, please follow

the steps below.

Select “Power Management Setup” in the main menu screen and
press <Enter>.

In the “ACPI Function” field, select “Enabled”.

In the “ACPI Suspend Type” field, select “S3(STR)”.

Appendix B - Using the Suspend to RAM Function

Press <Esc> to return to the main menu.

Select “Save & Exit Setup” and press <Enter>. Type <Y> and
press <Enter>.

Install Windows

98 by typing the following parameter. This is

to ensure that the ACPI function is supported.

[drive]:>setup /p j

If you have previously installed Windows

98, you need to

upgrade the system in order to support ACPI. Please contact
Microsoft for upgrade information.

The settings on the screen are for reference only. Your version may not be identical
to this one.

Содержание PT800-AL























































































































Результаты поиска

Содержание PT800-AL

Отзывы:

Похожие инструкции для PT800-AL

Бренды по названию

Популярные бренды

DFI PT800-AL, Руководство пользователя

Результаты поиска

Содержание PT800-AL

Отзывы:

Похожие инструкции для PT800-AL

Бренды по названию

Популярные бренды