manualshive.com logo in svg

DFI PT800-AL, Руководство пользователя

Поделиться
Скачать
DFI PT800-AL Скачать руководство пользователя страница 69

68

3

BIOS Setup

Onboard LAN Boot ROM

Enable this field if you wish to use the boot ROM (instead of a
disk drive) to boot-up the system and access the local area net-
work directly.

If you wish to change the boot ROM’s settings, type the <Shift>
and <F10> keys simultaneously when prompted during boot-up.
Take note: you will be able to access the boot ROM’s program
(by typing <Shift> + <F10>) only when this field is enabled.

OnChip USB Controller

This field is used to select the USB ports you want Enabled.

OnChip EHCI Controller

If you are using USB 2.0, this field must be set to Enabled.

USB Keyboard Support

If you are using a USB keyboard under DOS, set this field to
Enabled.

USB Mouse Support

This field is used to enable or disable the USB mouse. It can be
configured only if the “USB Controller” field is enabled.

Содержание PT800-AL























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды