DFI PT800-AL страница 79 Скачать руководство пользователя

Страница: 79 / 118

BIOS Setup

3.1.6 PnP/PCI Configurations

This section shows how to configure the PCI bus system. It cov-
ers some very technical items and it is strongly recommended
that only experienced users should make any changes to the de-
fault settings.

3.1.6.1 PNP OS Installed

The default setting is “No”. The BIOS will detect the Plug and
Play devices for some compatible resources.

3.1.6.2 Reset Configuration Data

Enabled

The BIOS will reset the Extended System Configura-
tion Data (ESCD) once automatically. It will then rec-
reate a new set of configuration data.

Disabled

The BIOS will not reset the configuration data.

3.1.6.3 Resources Controlled By

The Award Plug and Play BIOS has the capability to automatically
configure all of the boot and Plug and Play compatible devices.

Auto(ESCD)

The system will automatically detect the settings
for you.

Manual

Choose the specific IRQ resources in the “IRQ
Resources” field.

The settings on the screen are for reference only. Your version may not be identical
to this one.

Содержание PT800-AL























































































































Результаты поиска

Содержание PT800-AL

Отзывы:

Похожие инструкции для PT800-AL

Бренды по названию

Популярные бренды

DFI PT800-AL, Руководство пользователя

Результаты поиска

Содержание PT800-AL

Отзывы:

Похожие инструкции для PT800-AL

Бренды по названию

Популярные бренды