DFI PL610-C622 Скачать руководство пользователя страница 36

Страница: 36 / 54

www.d

.com

Chapter 3 BIOS Setup

Chapter 3

SIO AST2500

This section configures the system super I/O chip parameters.

Confi gure Serial port using
options: [Disable] No Con-
figuration [Enable] User
Confi guration [Auto] EFI/
OS chooses confi guration

Serial Port A

Base I/O Address
Interrupt

Advanced

Help

↑

↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←

→



Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

<3F8>
<IRQ4>

Serial Port A

Configure the settings to use the serial port.

Disable

No configuration

Enable

User con

guration

H2O IPMI Configuration

This section configures the H2O IPMI (Intelligent Platform Managment Interface).

IPMI Support

Enable or disable IPMI Support.

BMC Warm Up Time

Set the max. waiting time period from POST to BMC ready in seconds.

ACPI SPMI Table

Enable or disable the ACPI SPMI Table for IPMI driver installation.

Boot Option Support

Enable or disable IPMI boot option function.

Case Open Alert

Enable or disable buzzer beep when case is open. When disabled, system will clean

case open status.

Clean Case Open Status

Select this field and press Enter, system will clean the case open status.

Advanced

Help

↑

↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←

→



Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

Enable/Disable IPMI Sup-
port. Note: If changing to
enable, BMC detailed in-
formation only valid after
rebooting.

IPMI Support

BMC Warm Up Time

System Interface Type
IPMI Base Address for OS
IPMI Base Address for POST
IPMI Base Address for SMM

BMC Status
BMC Firmware Version
IPMI Specifi cation Version
BMC MAC Address

ACPI SPMI Table
Boot Option Support

Case Open Status

Case Open Alert
Clean Case Open Status



BMC Confi guration



SDR List

Execute H2O IPMI Utility

[60]

KCS
CA2/CA3
CA2/CA3
CA2/CA3

OK
B187.06A
2.0
00:C0:A8:12:34:58

Rev. 5.0

Содержание PL610-C622























































Результаты поиска

Содержание PL610-C622

Отзывы:

Похожие инструкции для PL610-C622

Бренды по названию

Популярные бренды

DFI PL610-C622, Руководство пользователя

Результаты поиска

Содержание PL610-C622

Отзывы:

Похожие инструкции для PL610-C622

Бренды по названию

Популярные бренды