DFI PL610-C622 Скачать руководство пользователя страница 18

Страница: 18 / 54

www.d

.com

Chapter 2 Hardware Installation

Chapter 2

USB Ports

The USB device allows data exchange between your computer and a wide range of simultane-

ously accessible external Plug and Play peripherals.

The system board is equipped with 2 onboard USB 2.0 ports (USB 1-2) and 1 vertical USB 2.0

port (USB 3). The 10-pin connector allows you to connect 2 additional USB 2.0 ports (USB

4-5). The 20-pin connector allows you to connect 2 additional USB 3.0 ports (USB 5-6). The

additional USB ports may be mounted on a card-edge bracket. Install the card-edge bracket

to an available slot at the rear of the system chassis and then insert the USB port cables to a

connector.

BIOS Setting

Configure these onboard USB devices in the Advanced menu (“USB Configuration” submenu)

of the BIOS. Refer to the chapter 3 for more information.

VCC

-Data

+Data

GND

VCC

-Data

+Data

GND

N.C.

1
2

USB 2.0

USB 2
USB 1

USB 2.0

Battery

USB 4-5

USB 5-6

USB 3

LAN Ports

MNG

Battery

10GLAN

GLAN

Features

• 1

i350-AM2

• 1

CS4227

• 1

RTL8211F

The LAN port allows the system board to connect to a local area network by means of a

network hub.

BIOS Setting

Configure the onboard LAN ports in the Advanced menu (“ACPI Configuration” submenu) of

the BIOS. Refer to the chapter 3 for more information.

Driver Installation

Install the LAN drivers. Refer to the chapter 4 for more information.

USB 2.0

VCC

GND

Data+

Data-

D-

GND

TX+

GND

RX+

PWR

D+

D-

GND

TX+

GND

RX+

PWR

er Current Protection

D+

USB 3.0

Содержание PL610-C622























































Результаты поиска

Содержание PL610-C622

Отзывы:

DFI PL610-C622, Руководство пользователя, Страница: 18 / 54

Результаты поиска

Содержание PL610-C622

Отзывы: