DFI PL610-C622 Скачать руководство пользователя страница 33

Страница: 33 / 54

www.d

.com

Chapter 3 BIOS Setup

Chapter 3

USB Configuration

This section is used to configure the parameters of the USB device.

Legacy USB Support

Disabled

Disable USB keyboard/mouse/storage support under UEFI and DOS environment.

Enabled

Enable USB keyboard/mouse/storage support under UEFI and DOS environment.

UEFI Only

Enable USB keyboard/mouse/storage support under UEFI environment.

XHCI Hand-off

Enable or disable to clear XHCI controller ownership change SMI bit by BIOS.

USB keyboard/mouse/stor-
age support under UEFI

and DOS environment. It
will supporting UEFI en-
vironment only if set to
UEFI Only

USB Confi guration

Legacy USB Support

XHCI Hand-off

Advanced

Help

↑

↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←

→



Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

Rev. 5.0

PCI Express Configuration

This section configures settings relevant to PCI Express root ports.

PCIE port confi guration

CPU PCIE Confi guration



PCIE1



PCIE2



PCIE3



PCIE4

On board 10G LAN <Enabled>

Advanced

Help

↑

↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←

→



Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

Rev. 5.0

PCIE1/2/3/4

These sections configure PCIe ports.

On board 10G LAN

Enable or disable onboard 10G LAN. When it is set to enabled and the jumper JP14

is set to 2-3 on, half lanes of PCIE3 are used for onboard 10G LAN (PCH uplink) and

PCIE3 only has x4 function. When it is set to disabled and JP14 is set to 1-2 on, on-

board 10G LAN is not supported and PCIE3 has full x8 function.

Содержание PL610-C622























































Результаты поиска

Содержание PL610-C622

Отзывы:

Похожие инструкции для PL610-C622

Бренды по названию

Популярные бренды

DFI PL610-C622, Руководство пользователя

Результаты поиска

Содержание PL610-C622

Отзывы:

Похожие инструкции для PL610-C622

Бренды по названию

Популярные бренды