DFI PL610-C622 Скачать руководство пользователя страница 23

Страница: 23 / 54

www.d

.com

Chapter 2 Hardware Installation

Chapter 2

LEDs

I350 PE Wake LED

Battery

Expansion Slots

PCI Express x16 Slot

Install PCI Express x16 graphics card, that comply to the PCI Express specifications, into the

PCI Express x16 slot. To install a graphics card into the x16 slot, align the graphics card above

the slot then press it down firmly until it is completely seated in the slot. The retaining clip of

the slot will automatically hold the graphics card in place.

PCI Express x4 Slot

Install PCI Express cards such as network cards or other cards that comply to the PCI Express

specifications into the PCI Express x4 slot.

PCI Express x8 Slot

Install PCI Express cards such as network cards or other cards that comply to the PCI Express

specifications into the PCI Express x8 slot.

M.2 M Key Socket

The M.2 socket is the Next Generation Form Factor (NGFF) which is designed to support multiple

modules and make the M.2 more suitable in application for solid-state storage.

PCI Express x16

PCI Express x4

Battery

M.2

PCI Express x8

PCI Express x4

PCI Express x16

BMC Heartbeat LED

CONT Stat GRN LED

CONT Stat Amber LED

CONT Stat GRN LED indicates that status is good.

CONT Stat Amber LED indicates that status is bad.

BMC AST2500 Heartbeat LED indicates if the BMC SPI flash is programmed. The hardware mode

includes below blinking modes:

0Hz

Always dark means

rmware is not running or dead

0.1Hz

Abnormal mode, some interrupts are not serviced for over 2 seconds.

0.5Hz

Normal operation mode, ARM running on DRAM with interrupt monitor enabled

2Hz

ARM running on DRAM without interrupt enabled (instruction fetch from DRAM)

10Hz

ARM running on Flash (instruction fetch from

ash)

Содержание PL610-C622























































Результаты поиска

Содержание PL610-C622

Отзывы:

Похожие инструкции для PL610-C622

Бренды по названию

Популярные бренды

DFI PL610-C622, Руководство пользователя

Результаты поиска

Содержание PL610-C622

Отзывы:

Похожие инструкции для PL610-C622

Бренды по названию

Популярные бренды