DFI CH960-CM246 Скачать руководство пользователя

Страница: 58 / 73

Chapter 6

www.d

.com

Chapter 6 RAID

Settings

To enable the RAID function, the following settings are required.

1. Connect the Serial ATA drives.

2. Configure Serial ATA in the AMI BIOS.

3. Configure RAID in the RAID BIOS.

4. Install the RAID driver during OS installation.

5. Install the Intel Rapid Storage Drivers.

Step 1: Connect the Serial ATA Drives

Refer to chapter 2 for details on connecting the Serial ATA drives.

Important:

1. Make sure you have installed the Serial ATA drives and connected the data cables

otherwise you won’t be able to enter the RAID BIOS utility.

2. Treat the cables with extreme caution especially while creating RAID. A damaged

cable will ruin the entire installation process and operating system. The system will

not boot and you will lost all data in the hard drives. Please give special attention

to this warning because there is no way of recovering back the data.

Step 2: Configure Serial ATA in the AMI BIOS

1. Power-on the system then press <Del> to enter the main menu of the AMI BIOS.

2. Configure Serial ATA in the appropriate fields.

3. Save the changes in the Save & Exit menu.

4. Reboot the system.

Step 3: Configure RAID in the RAID BIOS

When the system powers-up and all drives have been detected, the Intel RAID BIOS status

message screen will appear. Press the <Ctrl> and <I> keys simultaneously to enter the utility.

The utility allows you to build a RAID system on Serial ATA drives.

Chapter 6 - RAID (CH960-CM246/QM370 only)

The system board allows configuring RAID on Serial ATA drives. It supports RAID 0, RAID 1,

RAID 5 and RAID 10.

RAID Levels

RAID 0 (Striped Disk Array without Fault Tolerance)

RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved

stacks. Data is divided into stripes and each stripe is written alternately between two disk

drives. This improves the I/O performance of the drives at different channel; however it is not

fault tolerant. A failed disk will result in data loss in the disk array.

RAID 1 (Mirroring Disk Array with Fault Tolerance)

RAID 1 copies and maintains an identical image of the data from one drive to the other drive.

If a drive fails to function, the disk array management software directs all applications to the

other drive since it contains a complete copy of the drive’s data. This enhances data protection

and increases fault tolerance to the entire system. Use two new drives or an existing drive and

a new drive but the size of the new drive must be the same or larger than the existing drive.

RAID 5

RAID 5 stripes data and parity information across hard drives. It is fault tolerant and provides

better hard drive performance and more storage capacity.

RAID 10 (Mirroring and Striping)

RAID 10 is a combination of data striping and data mirroring providing the benefits of both

RAID 0 and RAID 1. Use four new drives or an existing drive and three new drives for this

configuration.

RAID Level

Min. Drives

Protection

Description

RAID 0

None

Data striping without redundancy

RAID 1

Single Drive Failure

Disk mirroring

RAID 5

Single Drive Failure

Block-level data striping with

distributed parity

RAID 10

1 Disk Per Mirrored

Stripe (not same mirror)

Combination of RAID 0 (data striping)

and RAID 1 (mirroring)

Содержание CH960-CM246










































































Результаты поиска

Содержание CH960-CM246

Отзывы:

Похожие инструкции для CH960-CM246

Бренды по названию

Популярные бренды

DFI CH960-CM246, Руководство пользователя

Результаты поиска

Содержание CH960-CM246

Отзывы:

Похожие инструкции для CH960-CM246

Бренды по названию

Популярные бренды