Dexter Laundry OPL 30 Cycle 200G Express Скачать руководство пользователя страница 33

Страница: 33 / 71

Pressure Switch

SINGLE LEVEL

DUAL LEVEL

Adjustment

Mechinical Pressure switch VS Pressure Sensor

The Drawing below represents the Mechinical Pressure switch and wiring connections. After serial number

W1.15244.001 all washers were converted to the electronic pressure sensor 9732-315-001. If desired previ-

ous C-series machines can be upgraded to the electronic pressure sensor with Kit 9732-314-001, Kit includes

pressure sensor, hold downs, transformer, and wires. The Electronic pressure sensor wiring configuration is

represented in the Diagrams and Schematics in this manual.

Microprocessor, also called a CPU

The microprocessor is mounted vertically on the right side of the control trough. It controls all washer

functions and is held in place with 4 screws. There are 4 wiring connectors on the board for incoming

and outgoing signals. See Microprocessor drawing below for exact locations. The single red light on

the board shows if the microprocessor has power and if it is processing data. As shown in the drawing

below, the light should be on steady any time the washer has power to it. If the red light is flashing,

the microprocessor has stopped processing data. Remove power from the machine for 2 minutes to

reset board. Repower the washer and check the light to see if it is on steady. If the light is off, there is
no power to the board

Control Mounting Trough

Remove top panel to access control trough. (see Removing Top Panel) It sets on the right side of the

machine and holds the control PCB’s, transformers, and pressure switch.

Circuit Breaker/Fuse

The fuse (optional circuit breaker) mounts to the rear channel. It carries all of the controls in the

machine but does not include the motor. To reset the circuit breaker just push in the button. If you

have a fuse then remove fuseholder and fuse and replace with a 1.5 amp fast blow type fuse.

PCB Transformer Step-down 120/12

Small transformer mounted at front of control trough that has primary power of 120VAC and

secondary outputs of 12VAC

Main Controls Transformer 208-240/120

This transformer is mounted at the back of the control trough and

steps a range of 208 to 240 volts down to 120 volts for the controls.

There are two terminals on the controls transformer for incoming

power. Note: All washers have a controls transformer. Always

check the incoming voltage and use the appropriate transformer

terminal when installing ALL washers.

Main Relay Input/Output-Printed Circuit Board

Please be sure to be grounded to machine before removal of this

board. PCB mounting horizontal in control trough towards front of

machine. Remove 4 mounting nuts.

Display LED Printed Circuit Board

The selector switch is mounted in the center of the control panel and is held in place with five nuts.

It allows the selection of hot, warm, or cold water temperatures. Note: Do not over tighten on
reinstallation as the switch can be damaged, stay pushed in and will cause erratic display

Pressure Switch :Caution (Not recommended by Factory!)

Changing Factory

preset adjustment voids all factory water usage specifications.

The pressure switch sets the water level in the washer. As the water level rises, it compresses the air in

the pressure switch hose. When the washer reaches the desired water level, the compressed air in the

pressure switch hose opens the contacts in the switch, shutting off the water. When at the empty level,

the pressure switch contacts are closed allowing the machine to either spin or fill with water. The 1/4”

screw in the middle of the switch adjusts the water level. Turning it clockwise 1/8 of a turn will raise the

water level 1/4 of an inch. Counter clockwise will lower the water level. Before making any adjustments

of the pressure switch, drain the tub and blow the hose clear of possible water bubbles which can cause

erratic pressure switch operation. With no load, the water level should be approximately at the bottom to

1/2” to 1” up from the bottom of the glass on ALL models.

Part # 8533-096-001 11/16

Содержание OPL 30 Cycle 200G Express








































































Результаты поиска

Содержание OPL 30 Cycle 200G Express

Отзывы:

Похожие инструкции для OPL 30 Cycle 200G Express

Бренды по названию

Популярные бренды

Dexter Laundry OPL 30 Cycle 200G Express, Руководство по запчастям и обслуживанию

Результаты поиска

Содержание OPL 30 Cycle 200G Express

Отзывы:

Похожие инструкции для OPL 30 Cycle 200G Express

Бренды по названию

Популярные бренды