Dexter Laundry OPL 30 Cycle 200G Express Скачать руководство пользователя страница 30

Страница: 30 / 71

Loading Door Disassembly

Loading Door Reassembly

Step 1: Remove the loading

door as outlined above.

Lay the door on a flat

surface with the glass

down

Step 2: While holding down

on the door glass, lift

up on the door ring

and roll back the lip of

the gasket with your

fingers.

tep 3: Work all the way

around the gasket and

the glass is out.

Step 1: Lay the door ring face

down on a flat surface.

Start the glass into one

side of the door gasket.

Step 2: Use one hand

underneath to push

the gasket out and the

other hand on the top

pulling the gasket in

Step 3: The front lip of the

door gasket should

be checked for proper

seating.

Front Control Panel Name Plate Decal

The name plate on washer front is adhesive backed.

Front Control Panel Name Plate Removal

The name plate may be removed by simply peeling it off.

Re-Installation of Name Plate

Step 1: Remove any remaining glue from the control panel.

Step 2: Before removing the paper backing from the name plate, check fit to the control panel. The

program push buttons are the locating guides.

Step 3: Remove the paper backing from the right side of the name plate, position it on the panel and

press right end into place. Peel the backing from the left end and press into place.

Door Locking Gear Motor

The door locking gear motor is powered shut with

control voltage to lock the door and releases when

voltage is removed. It is located in the left front

corner of the washer.

Thermoactuators

The thermoactuators are a safety device that

keeps the door from immediately unlocking if

power is lost while the machine is operating.

They are mounted above the door locking gear

motor.

Lock Thermoactuator

Control voltage is applied to the lock

thermoactuator at the beginning of the cycle

making it extend and block the door locking

gear motor. This keeps the door locked for

approximately two minutes after a power failure

occurs. The lock thermoactuator does not delay

the door opening at the end of a normal cycle.

Unlock Thermoactuator

To insure that the lock thermoactuator has

retracted by the end of the cycle, one minute prior

to the end of the cycle, the unlock thermoactuator

is powered with control voltage making it extend

and unblock the door locking gear motor.

Drive Belt Removal

Turn the drive belt(s) off the basket pulley first and

then remove from the motor pulley.

NOTE: Reverse this procedure for

installation.

Thermoactuator

Drive Belt

Part # 8533-096-001 11/16

Содержание OPL 30 Cycle 200G Express








































































Результаты поиска

Содержание OPL 30 Cycle 200G Express

Отзывы:

Похожие инструкции для OPL 30 Cycle 200G Express

Бренды по названию

Популярные бренды

Dexter Laundry OPL 30 Cycle 200G Express, Руководство по запчастям и обслуживанию

Результаты поиска

Содержание OPL 30 Cycle 200G Express

Отзывы:

Похожие инструкции для OPL 30 Cycle 200G Express

Бренды по названию

Популярные бренды