background image

Prohibited! Do not attempt to open, touch, or pro-

ceed before referring to the manual or unless quali-

fied.

Mandatory! Read all supporting documentation be-

fore operating or maintaining equipment.

 

Mandatory! Disconnect power before servicing 

equipment.

Mandatory! Lock out and tag out  before servicing 

this equipment.

Mandatory! Disconnect water supply before servic-

ing equipment.

Mandatory! Children should be supervised to ensure 

they do not  operate equipment.

A machine should not be allowed to 

operated if any of the following occur:

• Excessively high water level.

• Machine is not connected to a properly grounded 

circuit.

• Loading door does not remain securely locked 

during the entire cycle.

• Vibration or shaking from an inadequate mounting 

or foundation.

Table of Contents

Section 1: 

Machine Mounting & Installation
T-650 Deminsions .................................... 12 ,14
T-950 Deminsions .................................... 13, 15 
T-1450 Deminsions ................................... 13, 16

Section 2: 

Machine Installation  & Operating Instructions
Basic Installation ....................................... 20,21
Electrical Connections & Fusing Requirements .21
Liquid Chemical Injection ................................22
Machine Operating Instructions ................. 23-25

Section 3: 

Machine Programming Instructions
Programming Instructions  ........................ 28,29
30 Preset Cycle Descriptions.........................30-38

Section 4: 

Trouble Shooting
Rapid Advance Mode ......................................40
Diagnostic Test Cycle..........................................41
Input/Output Board Diagram..............................43
Common Troubleshooting Solutions.............44-50
Electrical Schematic / Bath Descriptions ..... 51-52

Section 5: 

Machine Service Procedures
Top, Front, Back Panel Removal ......................54
Drain Valve Access .........................................54
Drain Valve Cleaning ......................................54
Vacuum Breaker/ Air Gap ...............................54
Water Valves .................................................54
Door Lock Assembly / Operation .....................55
Adjustment of the Door Lock Assembly ......55-56
Adjusting the Loading Door ............................57
Loading Door Removal ...................................57
Loading Door Hinge Removal ..........................57
Loading Door Disassembly .............................58
Loading Door Reassembly ..............................58
Control Panel Name Plate Decal ......................58

Dexter Safety 

Guidelines

FOR SAFETY

1.  Always shut off power and water 

supply.

2.  Do not overload the washer.

3.  Do not attempt to open door if cylinder 

is in motion or contains water.

4.  Do not mechanically force or override 

door lock in any way.

5.  Do not bypass any safety devices of 

this washer.

6.  Do not use volatile or flammable 

substances in or near this washer.

7.  Keep all panels in place. They protect 

against shock and injury and add 

rigidity to the washer.

To activate your warranty, be sure to 

return your  warranty form to the factory. 

Please have serial number and model 

ready when calling for assistance.

  

WARNING

These washers are equipped with devices and 

features relating to their safe operation. To 

avoid injury or electrical shock, do not perform 

and service, unless qualified to do so.

 

Part # 8533-096-001 11/16

Part # 8533-096-001  11/16

8

9

Содержание OPL 30 Cycle 200G Express








































































Отзывы: