16
English
• Check that the saw arm does not move when the bevel
clamp handle (21) is locked at a random (not preset) angle.
Rail guide adjustment (fig. J)
• Regularly check the rails for clearance.
• To reduce clearance, gradually rotate the set screw (57)
clockwise while sliding the saw head back and forth. Adjust
the clearance to be as small as possible without causing any
slide resistance.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions
and applicable regulations.
WARNING: To reduce the risk of serious
personal injury, turn tool off and disconnect
tool from power source before making any
adjustments or removing/installing attachments
or accessories.
Be sure the trigger switch is in the
OFF position. An accidental start-up can cause injury.
Ensure the machine is placed to satisfy your ergonomic
conditions in terms of table height and stability. The machine site
shall be chosen so that the operator has a good overview and
enough free surrounding space around the machine that allows
handling of the workpiece without any restrictions.
To reduce effects of vibration make sure the environment
temperature is not too cold, machine and accessory is well
maintained and the workpiece size is suitable for this machine.
The attention of UK users is drawn to the “woodworking
machines regulations 1974” and any subsequent amendments.
Prior to operation:
• Install the appropriate saw blade. Do not use excessively
worn blades. The maximum rotation speed of the tool must
not exceed that of the saw blade.
• Do not attempt to cut excessively small pieces.
• Allow the blade to cut freely. Do not force.
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles are tight.
• Secure the workpiece.
• Although this saw will cut wood and many nonferrous
materials,
these operating instructions refer to the cutting of wood only.
The same guide-lines apply to the other materials.
Do not cut ferrous (iron and steel) materials, fibre cement or
masonry with this saw!
• Make sure to use the kerf plate. Do not operate the machine
if the kerf slot is wider than 10 mm.
Switching on and off (fig. K)
A hole (58) is provided in the on/ off switch (1) for insertion of a
padlock to lock the tool.
• To run the tool, press the on/off switch (1).
• To stop the tool, release the switch.
Body and hand position
Proper positioning of your body and hands when operating the
mitre saw will make cutting easier, more accurate and safer.
• Never place your hands near the cutting area.
• Place your hands no closer than 150 mm from the blade.
• Hold the workpiece tightly to the table and the fence when
cutting. Keep your hands in position until the switch has
been released and the blade has completely stopped.
• Always make dry runs (without power) before finish cuts so
that you can check the path of the blade.
• Do not cross your hands.
• Keep both feet firmly on the floor and maintain proper
balance.
• As you move the saw arm left and right, follow it and stand
slightly to the side of the saw blade.
• Sight through the guard louvres when following a pencil line.
MIter Control (fig. E1)
The mitre lever (4) and mitre latch (5) allows the saw to mitre 60
left and
50 right.
To miter the saw:
• Release the mitre lever (4) and depress the mitre latch (5)
and set the mitre angle desired on the miter scale.
• Push down on the mitre lever (4) to lock the saw table in
place.
Bevel Control (fig. H1, H4)
The bevel latch levers (20) and bevel clamp handle (21) allows
the saw to bevel 48º left and right. Your saw has two bevel latch
levers (20), one on either side of the rear support housing. Only
one needs to be used to move the bevel to either direction. The
bevel clamp handle (21) is on top of the rear support housing.
To bevel the saw:
• Loosen the bevel clamp handle (21). Lift one of the levers
to approximately 45º and set the bevel angle desired on
the bevel scale (15). Two bevel scales are provided for
convenience.
• Lock the bevel clamp handle (21) to lock the bevel in place.
The bevel latch levers (20) can be lifted vertically to override
the common stop angles.
Slide Stop (fig. T)
The slide stop (18) control positions your saws rails so that
the largest possible verticle moldings can be cut. ALWAYS
TIGHTEN THE RAIL LOCK KNOB WHEN USING THE SLIDE
STOP TO PREVENT THE SLIDE SYSTEM FROM MOVING
UNINTENTIONALLY
Rail Lock Knob (fig. A1, T)
The rail lock knob (16) allows you to lock the saw head firmly to
keep it from sliding on the rails. This is necessary when making
certain cuts or when transporting the saw.
Grooving Stop (fig. A1, R)
The grooving stop (17) allows for groove cutting. Flipping the
lever toward the front of the saw and adjusting the thumbscrew
changes the depth of the groove cut. Flipping the lever toward
the rear of the saw bypasses the grooving stop.
Содержание DW717XPS
