DeWalt DW717XPS Скачать руководство пользователя страница 14

Страница: 14 / 24

English

than those recommended in this instruction manual

may present a risk of personal injury.

21.

Have your tool repaired by a qualified person.

This electric tool complies relevant safety rules. Repairs

should only be carried out by qualified persons using original

spare parts; otherwise this may result in considerable danger

to the user.

Additional Safety Rules for Mitre Saws

• The machine is provided with a special configured power

supply cord which can only be replaced by the manufacturer

or its authorised service agent.

• Before starting any cutting operation, ensure that the

machine is located on an flat and stable surface.

• Do not use the saw to cut other materials than those

recommended by the manufacturer.

• Do not operate the machine without guards in position, or if

guards do not function or are not maintained properly.

• Ensure that the arm is securely fixed when performing bevel

cuts.

• Keep the floor area around the machine level, well-

maintained and free of loose materials, e.g., chips and cut-

offs.

• Use correctly sharpened saw blades. Observe the maximum

speed mark on the saw blade. The marked maximum speed

shall always be greater than or at least equal to the speed

marked on the rating plate.

• Make sure all locking knobs and clamp handles are tight

before starting any operation.

• Never place either hand in the blade area when the saw is

connected to the electrical power source.

• Never attempt to stop a machine in motion rapidly by

jamming a tool or other means against the blade; serious

accidents can occur.

• Before using any accessory consult the instruction manual.

The improper use of an accessory can cause damage.

• Use a holder or wear gloves when handling a saw blade or

rough material.

  •  Ensure that the saw blade is mounted correctly before use.
  •  Make sure that the blade rotates in the correct direction.
  •  Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the

Technical Data

. Use only the blades specified in this

manual, complying with EN 847-1.

  •  Consider applying specially designed noise-reduction blades.
  •  Do not use HIGH SPEED STEEL blades.
  •  Do not use cracked or damaged saw blades.
  •  Do not use any abrasive or diamond discs.
  •  Never use your saw without the kerf plate.
  •  Raise the blade from the kerf in the workpiece prior to releasing

the switch.

• Do not wedge anything against the fan to hold the motor

shaft.

• The blade guard on your saw will automatically raise when

the arm is brought down; it will lower over the blade when

head lock up release lever (12) is pushed.

• Never raise the blade guard manually unless the saw is

switched off. The guard can be raised by hand when

installing or removing saw blades or for inspection of the saw.

• Check periodically that the motor air slots are clean and free

of chips.

• Replace the kerf plate when worn.
• Disconnect the machine from the mains before carrying out

any maintenance work or when changing the blade.

• Never perform any cleaning or maintenance work when

the machine is still running and the head is not in the rest

position.

• When possible, always mount the machine to a bench.
• If you use an LED to indicate the cutting line, make sure that

the LED is of class 2 according to EN 62471. Do not replace

an LED diode with a different type. If damaged, have the LED

repaired by an authorised repair agent.

•

The front section of the guard is louvered for visibility while

cutting. Although the louvers dramatically reduce flying

debris, they are openings in the guard and safety glasses
should be worn at all times when viewing through the
louvers.

• Connect the saw to a dust collection device when sawing

wood. Always consider factors which influence exposure of

dust such as:

-– type of material to be machined (chip board produces

more dust than wood);

    -– sharpness of the saw blade;
    -–  correct adjustment of the saw blade.
    -– dust extractor with air velocity not less than 20 m/s.
     Ensure that the local extraction as well as hoods, baffles and

chutes are properly adjusted.

• Please be aware of the following factors influencing exposure

to noise:

    -–  use saw blades designed to reduce the emitted noise;
    -– use only well sharpened saw blades;
  •  Machine maintenance shall be conducted periodically;
  •  Provide adequate general or localized lighting;
  •  Ensure the operator is adequately trained in the use,

adjustment and operation of the machine;

• Ensure that any spacers and spindle rings are suitable for the

purpose as stated in this manual.

• Refrain from removing any cut-offs or other parts of the

workpiece from the cutting area while the machine is running

and the saw head is not in the rest position.

• Never cut workpieces shorter than 200 mm.
• Without additional support the machine is designed to

accept the maximum workpiece size of:

– Height 89 mm by width 302 mm by length 600 mm
– Longer workpieces need to be supported by suitable

additional table, e.g. DE7023. Always clamp the

workpiece safely.

• In case of an accident or machine failure immediately turn the