English
5
WARNING:
Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.
WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use.
Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
•
Air vents often cover moving parts and should be
avoided.
Loose clothes, jewelry or long hair can be
caught in moving parts.
•
An extension cord must have adequate wire size
(AWG or American Wire Gauge) for safety.
The smaller
the gauge number of the wire, the greater the capacity
of the cable, that is, 16 gauge has more capacity than 18
gauge. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. When using
more than one extension to make up the total length,
be sure each individual extension contains at least the
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Volts
Total length of Cord in Feet
(meters)
120 V
25 (7.6)
50 (15.2) 100 (30.5) 150 (45.7)
240 V
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
American Wire gauge
More
Than
not
More
Than
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Recommended
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz .......................hertz
min .....................minutes
or DC ......direct current
...................... Class I Construction
(grounded)
…/min ..............per minute
BPM ....................beats per minute
IPM .....................impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM ....................strokes per minute
A .........................amperes
W ........................watts
or AC ...........alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
no .......................no load speed
n .........................rated speed
......................earthing terminal
.....................safety alert symbol
.....................visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating.
D
e
WALT
tools are factory tested;
if this tool does not operate, check power supply.
COMPONENTS (FIG. A)
WARNING:
Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.
INTENDED USE
This cut off tool is designed for professional
cutting applications.
DO nOT
use under wet conditions or in presence of
flammable liquids or gases.
This cut off tool is a professional power tool.
DO nOT
let
children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Rotating the Gear Case (Fig. B, C)
nOTE:
This machine is assembled at the factory with the
spindle on right side of the unit for right handed operation.
Conversion From Right Handed to Left
Handed
1. Place unit on a firm, flat work surface.
2. Remove bail handle
6
by removing 2 hex bolts
16
, the
top insulators
17
and the bottom insulators
18
.
3. Remove guard by removing guard mounting nuts
13
.
4. Remove the 4 gear case mounting screws
14
.
5. Rotate gear case 180˚ without pulling gear case
15
away from the body of the tool.
nOTE:
If the gear case and motor housing become
separated by more than 1/8" (3 mm), the tool must be
serviced and re-assembled by a
D
e
WALT
service center.
Failure to have the tool serviced may cause brush, motor
and bearing failure.
6. Replace the 4 gear case mounting screws
14
and
tighten firmly to 30 in-lbs.
7. Reattach the guard so the shoe faces in the same
direction as the trigger switch handle
7
. Be sure the
guard is on the spindle bearing hub as far as it will go
and both guard tabs engage the slot in the spindle
bearing hub. Tighten guard mounting nuts
13
securely
to 50 in-lbs.
Содержание D28754
Страница 35: ......
