DeVilbiss AGMD Series Скачать руководство пользователя страница 28

Страница: 28 / 39

High-performance automatic gun

AGMD

1-1-AGMD-514&515-E-002-1

Fault

Possible causes

Corrective action

Steady paint leak at the
nozzle.

Worn or damaged paint nozzle
socket.
Worn or damaged needle.
Needle does not seal tightly
(control air line is not vented).

Replace paint nozzle.

Replace needle.

Check nozzle.

Assembly fault

High-performance
automatic spray gun
AGMD does not click
firmly into adapter and
releases by itself.

Elastic pressure piece is set too
low.

Elastic pressure piece is dirty
and dented.

Remove the high-
performance automatic spray
gun AGMD, adjust the elastic
pressure piece, and tighten
the lock screw.
Replace damaged pressure
piece.

High-performance
automatic spray gun
AGMD cannot be locked
into the adaptor or only
with exertion of force.

Elastic pressure piece sticks out
too far.

Remove the high-
performance automatic spray
gun AGMD, adjust the elastic
pressure piece, and tighten
the lock screw.

The high-performance
automatic spray gun
AGMD does not always
engage into the adapter.

Elastic pressure piece can be
turned manually.

Remove the high-
performance automatic spray
gun AGMD, adjust the elastic
pressure piece, and tighten
the lock screw.

Содержание AGMD Series








































Результаты поиска

Содержание AGMD Series

Отзывы:

Похожие инструкции для AGMD Series

Бренды по названию

Популярные бренды

DeVilbiss AGMD Series, Руководство по эксплуатации

Результаты поиска

Содержание AGMD Series

Отзывы:

Похожие инструкции для AGMD Series

Бренды по названию

Популярные бренды